Skip to content
Tutorials Center
My learning

Topics

Strength of Materials Tutorial

Learn Strength of Materials step by step: 49 lessons in 9 chapters with examples, quizzes, diagrams and practice.

Start learning →

of lessons completed

Getting Started

  1. 1 Course Map: How Strength of Materials Works Meet Strength of Materials: the nine-chapter plan, who the course is for, what you need first, and a hands-on first check of whether a steel bar will hold.
  2. 2 Loads, Supports and Free-Body Diagrams Learn the types of loads and supports, how to draw a free-body diagram, and how to find the reactions of a simply supported beam step by step.
  3. 3 Internal Forces and the Method of Sections Learn how to cut a member in your mind and find the internal axial force, shear force, bending moment and torque from equilibrium, with worked beam and bar examples.
  4. 4 Units, Assumptions and the Engineer's Toolkit Master the units of strength of materials (N, mm, MPa), conversions to psi, and the six standard assumptions behind every formula in this course.
  5. 5 Chapter 1 Review: Getting Started Review loads, supports, free-body diagrams, internal forces, units and assumptions with a one-page summary, recap table and a ten-question mixed quiz.

Stress and Strain

  1. 6 Stress and Strain: The Big Picture See why stress and strain, not force and elongation, let engineers compare any part with any material, and get a map of chapter 2 with its five lessons.
  2. 7 Normal Stress: Tension and Compression Learn to calculate normal stress in bars and posts with ฯƒ = P/A, size a rod for an allowable stress, and understand why the average stress is only valid away from the ends.
  3. 8 Shear and Bearing Stress in Connections Calculate shear stress in bolts, pins and rivets in single and double shear, bearing stress on plates, and punching shear, with worked examples and a joint checker.
  4. 9 Strain and the Stress-Strain Curve Understand normal and shear strain, read a tensile-test stress-strain curve for ductile steel, and learn yield strength, ultimate strength, ductility and toughness.
  5. 10 Hooke's Law and Material Properties Use Hooke's law ฯƒ = Eฮต, Poisson's ratio and the shear modulus G to calculate elongation and lateral contraction, and compare the stiffness of common engineering materials.
  6. 11 Chapter 2 Review: Stress and Strain Review normal stress, shear and bearing stress, strain, the stress-strain curve and Hooke's law with a summary sheet, recap table and a ten-question mixed quiz.

Axial Loading

  1. 12 Axial Loading: The Big Picture Preview chapter 3: bars loaded along their axis, how internal force changes along a stepped bar, and the lessons on deformation, indeterminate bars, heat and stress concentration.
  2. 13 Axial Deformation: ฮด = PL/AE Derive and use ฮด = PL/AE for the elongation of axially loaded bars, extend it to stepped and tapered bars, and understand axial stiffness with worked numerical examples.
  3. 14 Statically Indeterminate Axial Members Solve bars fixed between two walls and composite bars of two materials using equilibrium, compatibility and force-deformation relations, with worked numerical examples.
  4. 15 Thermal Stress and Thermal Expansion Compute free thermal expansion ฮดT = ฮฑLฮ”T, the compressive stress in a bar that cannot expand, and the stress when a small gap closes, with worked steel examples.
  5. 16 Stress Concentrations: Holes, Notches and Fillets Learn why holes and sharp corners raise local stress, how to use the stress concentration factor Kt with net-section stress, and design habits that reduce stress peaks.
  6. 17 Chapter 3 Review: Axial Loading Review axial deformation, indeterminate bars, thermal stress and stress concentrations with a one-page sheet, a recap table, a combined worked example and a ten-question quiz.

Torsion

  1. 18 Torsion: The Big Picture Preview chapter 4: how a torque twists a shaft, the three formulas for shear stress, angle of twist and power, and the lessons that follow.
  2. 19 The Torsion Formula for Circular Shafts Derive the torsion formula, understand the linear shear stress distribution, compute the polar moment J for solid and hollow shafts, and size a shaft for an allowable stress.
  3. 20 Angle of Twist and Power Transmission Calculate the angle of twist of a shaft with ฯ† = TL/(GJ), convert power and rpm to torque, and design a shaft for both strength and twist with worked examples.
  4. 21 Indeterminate Shafts and Thin-Walled Tubes Solve shafts fixed at both ends with compatibility of twist, then learn closed thin-walled tubes with shear flow and Bredt's formula ฯ„ = T/(2Aโ‚˜t), compared with open sections.
  5. 22 Chapter 4 Review: Torsion Review torsion of circular shafts, angle of twist, power transmission, indeterminate shafts and thin-walled tubes with a summary sheet, a recap table and a ten-question quiz.

Bending of Beams

  1. 23 Chapter 5 overview: bending of beams See the big picture of beam bending: loads, shear force, bending moment and stress, and what each lesson in this chapter teaches you.
  2. 24 Shear force and bending moment diagrams Learn the method of sections, sign conventions and the shortcut relations between load, shear and moment to draw V and M diagrams for beams.
  3. 25 The flexure formula: stress in a bent beam Derive and use the flexure formula ฯƒ = My/I. Find where bending stress is largest, use the section modulus and size a beam for an allowable stress.
  4. 26 Second moment of area and the parallel-axis theorem Compute centroids and second moments of area for rectangles, circles and built-up T- and I-sections using the parallel-axis theorem, step by step.
  5. 27 Chapter 5 review: bending of beams Review the beam analysis chain from reactions to shear, moment and bending stress, with a recap table, a beam-checker tool and a ten-question quiz.

Shear and Combined Loading

  1. 28 Chapter 6 overview: shear and combined loading Preview transverse shear stress, combined axial, bending and torsion loads, and Mohr's circle, and see how they fit together in this chapter.
  2. 29 Transverse shear stress in beams: ฯ„ = VQ/(Ib) Learn the shear formula ฯ„ = VQ/(Ib), find where beam shear stress peaks, and compute shear flow to space nails and glue lines in built-up beams.
  3. 30 Combined axial, bending and torsion Superpose axial, bending, shear and torsional stresses at a critical point. Includes eccentric loads, the middle-third rule and a bent, twisted shaft.
  4. 31 Stress transformation and Mohr's circle Rotate a plane stress state, find principal stresses and maximum shear with formulas and Mohr's circle, and avoid the in-plane versus absolute shear trap.
  5. 32 Chapter 6 review: shear and combined loading Review transverse shear stress, shear flow, combined loads and Mohr's circle with a recap table, a plane-stress calculator and a nine-question quiz.

Deflection and Buckling

  1. 33 Chapter 7 overview: deflection and buckling See why stiffness and stability matter as much as strength, and preview the methods for beam deflection and Euler column buckling in this chapter.
  2. 34 The elastic curve and the integration method Derive EI v'' = M(x) and integrate it with boundary conditions to find slope and deflection of cantilevers and simply supported beams, with numbers.
  3. 35 Superposition and standard cases Use the four standard beam cases and superposition to find deflections quickly, then solve a propped cantilever, a statically indeterminate beam, with numbers.
  4. 36 Euler buckling of columns Understand Euler column buckling: critical load, effective length factors, slenderness ratio, the Euler and Johnson curves, with worked steel column examples.
  5. 37 Chapter 7 review: deflection and buckling Review curvature, integration, standard deflection cases, superposition and Euler buckling, with a recap table, check tools and a nine-question quiz.

Failure Theories and Design

  1. 38 Chapter 8 overview: failure theories and design Learn how materials fail by yielding, fracture and fatigue, why one tensile test must predict failure under any stress state, and how design uses safety factors.
  2. 39 Yield criteria: Tresca and von Mises Check whether a ductile part yields under combined stresses with the Tresca maximum-shear and von Mises distortion-energy criteria, plus brittle fracture rules.
  3. 40 Fatigue and notches: failure under repeated loads Understand fatigue failure under repeated loads: stress amplitude, the S-N curve, endurance limit, notch effects Kt and Kf, and the Goodman mean-stress line.
  4. 41 Factor of safety and the design process Define the factor of safety, apply allowable-stress and load-factor design, size a shaft with the von Mises criterion, and find which failure mode governs.
  5. 42 Chapter 8 review: failure theories and design Review failure modes, Tresca and von Mises, fatigue, notches and factors of safety with a recap table, a shaft audit tool and a nine-question quiz.

Projects and Practice

  1. 43 Chapter 9 overview: projects and practice Apply everything you learned: two design projects, a ten-problem practice set with answers, a glossary, a cheat sheet and ideas for further study.
  2. 44 Project 1: design a floor beam Size a steel rectangular hollow beam for bending strength and a span over 360 deflection limit, find which check governs and plot V, M and deflection.
  3. 45 Project 2: design an A-frame bracket Design a wall bracket: find member forces by statics, size a tie rod for tension, a tube strut for buckling and a pin in double shear, then study the angle.
  4. 46 Practice set: ten mixed problems Ten mixed strength of materials problems on bending, shear, eccentric loads, Mohr's circle, von Mises, deflection, buckling and fatigue, with answers and a checker.
  5. 47 Glossary of strength of materials Aโ€“Z glossary of strength of materials terms such as stress, strain, section modulus, neutral axis, buckling and von Mises, with a concept map and flashcards.
  6. 48 Cheat sheet: all the formulas on one page One-page strength of materials formula sheet: stress, strain, axial, torsion, bending, shear, Mohr's circle, deflection, buckling and failure, with units and a toolbox.
  7. 49 Where to go next after strength of materials Plan your next steps after strength of materials: structures, materials science, dynamics, finite elements, fracture, plasticity and composites, with site tracks to follow.