Analog Electronics Tutorial
Learn Analog Electronics step by step: 46 lessons in 9 chapters with examples, quizzes, diagrams and practice.
Start learning →
of lessons completed
Getting Started
- Course map: how this analog electronics course works Meet the nine chapters of this analog electronics course, see who it is for, what you need to know first, and how to study it with live simulations.
- Ohm's law, power and Kirchhoff's laws Master voltage, current, resistance and power, then use Kirchhoff's current and voltage laws and a short Python solver to analyze real circuits.
- Voltage dividers and Thévenin equivalents Learn the voltage divider, why loading changes it, and how a Thévenin equivalent reduces any linear network to a source and a resistor, with simulations.
- Capacitors and the RC time constant Understand how a capacitor charges and discharges through a resistor, what the time constant RC means, and how to predict any point on the curve.
- Chapter 1 review: Getting Started Review Ohm's law, Kirchhoff's laws, voltage dividers, Thévenin equivalents and RC circuits with a recap table, a one-page picture and a ten-question quiz.
Diodes and Rectifiers
- Chapter 2 overview: the diode See the big picture of diodes and rectifiers: what a diode does, where it is used, and how the lessons in this chapter build from the junction to power supplies.
- The p-n junction and diode models Learn how a p-n junction makes a diode, use the Shockley equation, and solve diode circuits with ideal, constant-drop and load-line methods, with simulations.
- Rectifier circuits: half-wave, full-wave and bridge Build half-wave, full-wave and bridge rectifiers, calculate average output and peak inverse voltage, and size a smoothing capacitor for a given ripple.
- Zener regulators, clippers and protection diodes Design a Zener shunt regulator, build diode clippers, and protect circuits from voltage spikes, with worked numbers and simulations you can run.
- Chapter 2 review: Diodes and Rectifiers Review the diode curve, models, rectifiers, smoothing, Zener regulators and clippers with a one-page summary picture, recap table and a ten-question quiz.
Bipolar Transistors
- Chapter 3 overview: the bipolar transistor Get the big picture of the bipolar junction transistor: how a small base current controls a large collector current, and how this chapter builds from regions to amplifiers.
- How a BJT works: structure, equations and regions Understand how an NPN transistor works, use IC = beta times IB and the exponential law, identify cutoff, active and saturation, and find a Q point on the load line.
- The BJT as a switch: saturation, base resistors and loads Design a transistor switch: choose the base resistor for saturation, drive LEDs and relays from logic pins, and protect against inductive spikes, with calculations.
- The BJT small-signal model: gm, r-pi and a first amplifier Linearize the transistor around its Q point with the hybrid-pi model: compute gm, r-pi and ro, then find the gain and resistances of a common-emitter amplifier.
- Chapter 3 review: Bipolar Transistors Review how a BJT works, its regions, switch design and the hybrid-pi small-signal model with a summary picture, recap table and a ten-question practice quiz.
MOSFETs
- Chapter 4 overview: the MOSFET See the big picture of the MOSFET, the transistor behind almost every chip: how a gate voltage controls a channel, and how this chapter builds from the I-V curve to CMOS.
- MOSFET structure, regions and the square-law I-V curves Learn how an n-channel MOSFET is built, how the channel forms above threshold, the triode and saturation equations, and how to find the operating point.
- The MOSFET as a switch and the CMOS inverter Use a MOSFET as a low-loss switch, size the gate drive, then see how a PMOS and NMOS pair make the CMOS inverter and why chips spend power only when switching.
- The MOSFET small-signal model and the common-source amplifier Linearize a MOSFET at its bias point, compute gm and ro, draw the small-signal model and find the gain, input and output resistance of a common-source amplifier.
- Chapter 4 review: MOSFETs Review MOSFET structure, the triode and saturation equations, switch and CMOS design and the small-signal model, with a summary picture and a ten-question quiz.
Amplifier Basics and Biasing
- Chapter 5 overview: amplifier basics and biasing A map of chapter 5: what an amplifier does, how gain and decibels work, why transistors need biasing, and how the common-emitter stage ties it all together.
- Gain and decibels Learn voltage, current and power gain, how decibels turn multiplication into addition, and how source and load resistance change the gain you actually get.
- Biasing a bipolar transistor Learn why a transistor needs bias, how a DC load line locates the Q-point, and how to design a stable voltage-divider bias with worked numbers.
- The common-emitter amplifier Analyse a common-emitter BJT stage with the small-signal model: gain -RC/re, input and output resistance, coupling and bypass capacitors, and distortion limits.
- Chapter 5 review: amplifier basics and biasing Review gain, decibels, Q-point, divider bias and the common-emitter stage with a recap table, a design calculator, a frequency-response plot and a ten-question quiz.
Operational Amplifiers
- Chapter 6 overview: operational amplifiers Meet the op-amp: a high-gain building block that becomes precise with feedback. See the ideal rules, the circuits you will build, and the limits of real chips.
- The ideal op-amp and feedback Learn the two golden rules of the ideal op-amp and use them to derive the gain of the inverting and non-inverting amplifiers, plus the voltage follower.
- Op-amp circuits: summer, difference, integrator and differentiator Use the golden rules to design the summing amplifier, difference amplifier, integrator and differentiator, with worked numbers, CMRR from resistor tolerance and runnable demos.
- Real op-amp limits: bandwidth, slew rate and offset Understand why real op-amps run out of bandwidth, speed and accuracy: gain-bandwidth product, slew rate, input offset, bias current and output swing, with worked numbers.
- Chapter 6 review: operational amplifiers Review the ideal op-amp rules, the inverting and non-inverting amplifiers, summers, integrators and real-world limits with a recap table, tools and a ten-question quiz.
Filters and Oscillators
- Chapter 7 overview: filters and oscillators Preview chapter 7: how filters select frequencies, how active filters use op-amps, and how an amplifier with positive feedback becomes a sine-wave oscillator.
- RC filters: low-pass, high-pass and the -3 dB point Derive the first-order RC low-pass and high-pass filters, compute the cutoff frequency, gain and phase, read a Bode plot and avoid loading mistakes.
- Active filters: Sallen-Key and the meaning of Q Design second-order active filters with the Sallen-Key circuit: natural frequency, quality factor Q, Butterworth and other responses, and higher orders by cascading.
- Oscillators: the Barkhausen criteria and the Wien bridge Learn how an amplifier with positive feedback becomes a sine-wave oscillator: loop gain, phase, start-up, amplitude control, the Wien bridge, phase-shift and relaxation oscillators.
- Chapter 7 review: filters and oscillators Review RC filters, the -3 dB point, Sallen-Key active filters, Q, the Barkhausen criteria and Wien-bridge oscillators with a recap table, design tools and a ten-question quiz.
Power Supplies and Practical Design
- Chapter 8 overview: power supplies and practical design See how mains AC becomes clean DC: transformer, rectifier, filter capacitor and regulator, why each stage exists, and what practical design habits this chapter covers.
- Rectifiers, ripple and the filter capacitor Size a power-supply filter capacitor: half-wave, center-tap and bridge rectifiers, the ripple formula ΔV = I/(f·C), diode drops, surge current and capacitor ratings.
- Linear regulators: Zener, 78xx and low-dropout Design with linear regulators: Zener shunt regulators, the 7805 three-terminal regulator, dropout voltage, power dissipation, heat sinks and when an LDO is better.
- Switching regulators and practical power design Understand the buck converter: duty cycle, inductor ripple, output ripple and efficiency versus linear regulators, plus decoupling, layout and protection habits.
- Chapter 8 review: power supplies and practical design Review rectifiers, ripple, linear and switching regulators and practical decoupling with a recap table, a full supply design calculator and a ten-question quiz.
Projects and Practice
- Project: a 20 dB audio preamplifier Design an op-amp audio preamplifier from a specification: gain 11, 20 Hz to 20 kHz bandwidth, parts values, op-amp choice, offset and slew checks, and a test plan.
- Project: a sensor signal chain from bridge to ADC Design a strain-gauge signal chain: Wheatstone bridge, instrumentation amplifier gain, anti-aliasing filter, ADC range and resolution, with a numerical model of the whole chain.
- Practice problems: amplifiers, op-amps, filters and power Fourteen worked-out practice problems on gain, biasing, op-amps, filters, oscillators and power supplies, with a five-step method, hints, an answer checker and a solver.
- Glossary of analog electronics A searchable glossary of 45 analog electronics terms from gain and bias to op-amps, filters, oscillators and power supplies, each with a short definition and a lesson link.
- Analog electronics cheat sheet One-page recap of the key formulas for BJT amplifiers, op-amps, filters, oscillators and power supplies, with constants, rules of thumb and a formula calculator.
- Where to go next: further study in analog electronics Plan your next steps after analog electronics: deeper circuit theory, signals and systems, control, DSP, embedded systems and Arduino projects, plus topics worth exploring.