Skip to content
Tutorials Center
My learning

Topics

Power Electronics Tutorial

Learn Power Electronics step by step: 45 lessons in 9 chapters with examples, quizzes, diagrams and practice.

Start learning →

of lessons completed

Getting Started

  1. 1 Course Map: Welcome to Power Electronics Meet power electronics: what it is, who this course is for, what you need first, and a map of all nine chapters from switches to solar inverters.
  2. 2 Why Power Converters Switch Learn why switching converters beat linear regulators: how a fast on-off switch, duty cycle and averaging deliver power efficiently, with worked numbers.
  3. 3 Efficiency and the Loss Budget Calculate converter efficiency, split losses into conduction, switching, magnetic and gate-drive parts, and see how heat and frequency shape every design.
  4. 4 The Four Converter Families Sort every power converter into four families: rectifier, DC-DC converter, inverter and AC-AC converter, with examples, waveforms and a runnable harmonic demo.
  5. 5 Chapter 1 Review: Getting Started Review the foundations of power electronics: switching, duty cycle, efficiency and the four converter families, with a recap table and a ten-question quiz.

Power Semiconductors

  1. 6 Chapter 2 Overview: The Power Semiconductor Map Overview of power semiconductors: diodes, MOSFETs, IGBTs, thyristors, SiC and GaN, with a map of voltage, current and frequency ranges and what each device is for.
  2. 7 Power Diodes: PN, Schottky and Reverse Recovery Understand power diodes: forward voltage, conduction loss, Schottky versus PN junction, reverse recovery charge Qrr and how to choose a diode for a converter.
  3. 8 Power MOSFETs: Conduction, Gate Charge and Switching Learn how a power MOSFET works as a switch: RDS(on) and temperature, gate charge and the Miller plateau, the body diode, switching loss and ratings to check.
  4. 9 IGBTs, Thyristors and Wide-Bandgap Devices Compare IGBTs, thyristors, SiC MOSFETs and GaN transistors: structure, conduction and switching behavior, typical ratings, gate drive and where each device wins.
  5. 10 Chapter 2 Review: Power Semiconductors Review chapter 2: the switching overlap picture, a recap table of diodes, MOSFETs, IGBTs, thyristors, SiC and GaN, a switching-energy demo and a ten-question quiz.

Rectifiers and AC-DC Conversion

  1. 11 Chapter 3 Overview: From Mains AC to DC Overview of rectifiers and AC-DC conversion: half-wave, full-wave, filtered, three-phase and controlled rectifiers, with performance measures like form factor and ripple factor.
  2. 12 Single-Phase Rectifiers: Half-Wave and Bridge Work through half-wave, center-tapped and bridge rectifiers: current paths, average and rms output, peak inverse voltage, diode drops and worked examples.
  3. 13 Capacitor Filters and Ripple Learn how a smoothing capacitor works after a rectifier: ripple voltage estimate, conduction angle, peak diode current, power factor and how to size the capacitor.
  4. 14 Three-Phase and Thyristor Rectifiers Understand the six-pulse three-phase rectifier, its 1.35 V(LL) output and 6f ripple, and how thyristors with firing angle alpha control the average output voltage.
  5. 15 Chapter 3 Review: Rectifiers and AC-DC Conversion Review chapter 3: compare half-wave, bridge and three-phase rectifiers by average output, ripple and frequency, revisit filters and thyristors, and take a ten-question quiz.

DC-DC Converters

  1. 16 Chapter 4 Overview: DC-DC Converters Overview of DC-DC converters: buck, boost and buck-boost topologies, the voltage-gain curves versus duty cycle, continuous and discontinuous conduction and how to pick one.
  2. 17 The Buck Converter: Stepping Voltage Down Learn the buck converter from first principles: volt-second balance, inductor ripple, capacitor ripple, sizing L and C, CCM versus DCM, with a runnable simulation.
  3. 18 The Boost Converter: Stepping Voltage Up Understand the boost converter: how an inductor steps voltage up, the 1/(1-D) gain, inductor and capacitor design, why high duty cycles fail, and a runnable simulation.
  4. 19 The Buck-Boost Converter: Up, Down and Inverted Learn the inverting buck-boost converter: gain D/(1-D) with inverted polarity, inductor current and stresses, a runnable simulation, and Cuk, SEPIC and flyback relatives.
  5. 20 Chapter 4 Review: DC-DC Converters Review chapter 4: gain, inductor ripple, capacitor ripple and CCM boundary for the buck, boost and buck-boost converters, a design helper and a ten-question quiz.

Inverters and Motor Drives

  1. 21 Chapter 5 overview: inverters and motor drives See the big picture of DC-to-AC conversion: what an inverter does, where it is used, and how the lessons on bridges, three-phase inverters and motor drives fit together.
  2. 22 Single-phase inverters: half bridge and full bridge Build a single-phase inverter from switch legs: half-bridge and H-bridge, square-wave output, harmonics and THD, dead time, shoot-through and phase-shift control.
  3. 23 Three-phase inverters and six-step operation Learn the six-switch three-phase bridge: switch numbering, the six-step sequence, phase and line voltages, harmonics, THD and the current in an RL load.
  4. 24 Motor drives and V/f control Learn how a variable-frequency drive runs an induction motor: synchronous speed, slip, constant V/f, low-speed boost, field weakening, DC-link sizing and braking.
  5. 25 Chapter 5 review: inverters and motor drives Review square-wave and six-step inverters, harmonics, induction motor speed and V/f control with a recap table, a drive sizing calculator and a ten-question quiz.

Control and Modulation

  1. 26 Chapter 6 overview: control and modulation See how feedback and modulation turn a switching circuit into a regulated converter: PWM, harmonics, small-signal models, voltage-mode and current-mode control.
  2. 27 PWM and sinusoidal PWM Learn how a carrier and a reference make PWM: duty cycle, modulation index, frequency ratio, harmonics, unipolar and bipolar switching, third-harmonic injection and dead-time errors.
  3. 28 Voltage-mode control and small-signal models Derive the small-signal model of a buck converter, read its LC resonance on a Bode plot, and design a type III compensator for crossover, phase margin and stability.
  4. 29 Current-mode control Learn peak current-mode control of switching converters: the inner current loop, cycle-by-cycle current limit, subharmonic oscillation above 50 percent duty and slope compensation.
  5. 30 Chapter 6 review: control and modulation Review PWM, modulation index, harmonics, small-signal models, phase margin and current-mode control with a recap table, a loop-design helper and a ten-question quiz.

Magnetics and Thermal Design

  1. 31 Chapter 7 overview: magnetics and thermal design See why inductors, transformers and heat set the physical limits of every power converter, and how the lessons on cores, windings and thermal paths fit together.
  2. 32 Inductor design: cores, gaps, saturation and losses Design a gapped power inductor: energy in the gap, turns from peak flux density, gap length from L = ฮผ0NยฒAe/lg, saturation, skin effect, Litz wire and core loss.
  3. 33 Transformer design: Faraday's law, core size and leakage Design a high-frequency power transformer: Faraday's law, turns from flux swing, the area-product method, flux walking, leakage inductance, isolation and winding layout.
  4. 34 Thermal design: losses, junction temperature and heat sinks Estimate MOSFET conduction and switching loss, use the thermal resistance ladder to find junction temperature, choose a heat sink, and see how pulses and thermal feedback behave.
  5. 35 Chapter 7 review: magnetics and thermal design Review gapped inductors, Faraday's law, area product, core and copper loss, thermal resistance and heat sinks with a recap table, a combined design tool and a ten-question quiz.

Applications: Solar, EVs and Power Supplies

  1. 36 Chapter 8 overview: solar, EVs and power supplies Preview the three big applications of power electronics: solar inverters with MPPT, electric vehicle drivetrains and chargers, and mains power supplies with PFC.
  2. 37 Solar power and MPPT Model a solar module with the single-diode equation, find the maximum power point, track it with perturb and observe through a boost stage, and see how grid-tied inverters are built.
  3. 38 Electric vehicle power electronics Follow energy through an electric vehicle: battery, traction inverter, onboard and DC fast chargers, 12 V converter, 800 V systems, regenerative braking and the energy needed to drive.
  4. 39 Switching power supplies and PFC Follow an offline switching supply from the wall to a USB-C port: rectifier, power factor correction, flyback design equations, power factor and THD, standby and safety.
  5. 40 Chapter 8 review: solar, EVs and power supplies Review solar I-V curves and MPPT, EV drivetrain and charging, and PFC and flyback supplies with a recap table, an efficiency-chain calculator and a ten-question quiz.

Projects and Practice

  1. 41 Project: design and simulate a buck converter Design a 12 V to 3.3 V, 5 A synchronous buck converter end to end: duty cycle, inductor, output capacitor, losses and efficiency, then verify it with a switching simulation.
  2. 42 Practice problems: inverters, control, magnetics, thermal and applications Ten worked-calculation problems from chapters 5 to 8: inverter voltages, motor speed, V/f, SPWM, inductor and transformer turns, heat sinks, solar fill factor and flyback turns ratio.
  3. 43 Glossary of power electronics A searchable glossary of about 80 power electronics terms: switches, converters, inverters, control, magnetics, thermal design and applications, with a flashcard game.
  4. 44 Cheat sheet: power electronics formulas on one page A one-page power electronics cheat sheet: converter ratios, ripple, inverter voltages, modulation, magnetics, thermal and application formulas with typical values and a topology chooser.
  5. 45 Where to go next: further study in power electronics Plan your next steps after this course: neighbouring subjects on this site, simulation tools, hardware projects, standards and a starter simulation you can modify.