Skip to content
Tutorials Center
My learning

Topics

Lesson 18 of 49 · Drag and Performance

Types of drag and drag buildup

Learn the difference between form drag and friction drag, why streamlining works, the drag crisis, and how to estimate an aircraft's zero-lift drag with a component buildup.

The boundary layer gave us skin-friction drag. But the total drag of an object is more than friction. A flat plate held broadside to the wind has almost no skin friction yet a huge drag. In this lesson you will separate friction drag from pressure (form) drag, see why streamlining shrinks the wake, and learn the engineer's standard method for estimating an aircraft's zero-lift drag: the component buildup.

What you will learn

  • How pressure drag arises from a separated wake and how streamlining reduces it.
  • Typical drag coefficients of simple shapes, and what the drag crisis is.
  • What interference drag is and how to reduce it.
  • How to estimate CD0 by adding up the drag of each component.

Key terms

Form (pressure) drag: drag from the pressure difference between the front and the wake-filled rear of a body.

Wake: the region of slow, turbulent air behind a body.

Frontal area: the area of the body projected onto a plane perpendicular to the flow; the reference area for bluff bodies.

Wetted area (Swet): the total surface area in contact with the flow.

Form factor (FF): a multiplier greater than 1 that raises the friction drag of a component to include its form drag.

Two panels comparing flow around a cylinder with a wide wake and a streamlined strut with a thin wake, each with its drag coefficient.
Same width, very different drag: shape decides how much the flow separates.

Pressure drag and the wake

At the front of any body the flow stagnates and the pressure is high. If the flow stays attached around to the rear, the pressure rises again there and nearly cancels the front pressure: the net force from pressure is almost zero (d'Alembert's paradox at the ideal limit). If the flow separates, a low-pressure wake sits behind the body and the pressure at the rear is lower than at the front. The difference pushes the body backward. That net push is form drag.

The size of the wake sets the drag, so:

  • A bluff body (flat plate across the flow, a cylinder) has a wide wake and form drag far larger than its friction drag.
  • A streamlined body has a long, gentle taper on the rear so that the flow stays attached. Its drag is mostly friction.

Typical drag coefficients based on frontal area, for Reynolds numbers in the ordinary range, give a feel:

Shape (broadside to the flow) CD (approximate)
Flat plate, face-on about 1.2
Long cylinder, across the flow about 1.0 to 1.2
Sphere about 0.47
Streamlined strut or teardrop about 0.04 to 0.1

For a streamlined body such as an airship hull or a strut, designers instead quote CD based on wetted area or volume, because friction dominates.

The drag crisis

For a sphere or cylinder the drag coefficient is not constant. In the range of Reynolds numbers where the boundary layer is laminar when it separates, CD is high. At a Reynolds number of order 3 × 10⁵ (it varies with surface roughness and the free-stream turbulence), the boundary layer turns turbulent before it separates, sticks on longer, and the wake shrinks. CD falls sharply: the drag crisis. Golf-ball dimples and the seams on a cricket ball trigger turbulence early so that the ball is past the crisis at normal speeds.

Interference drag

Where two components meet (a wing root and a fuselage, a strut and a wing), the two boundary layers mix and the local pressure field changes. The total drag of the pair exceeds the sum of the separate drags. Designers reduce this with fairings and fillets that smooth the corner and with careful positioning, such as a low or high wing that meets the body at about a right angle.

Estimating CD0: the component buildup

At zero lift, drag is parasite drag. To estimate it for an airplane, add the contributions of every part, each referred to the wing reference area S:

Text
CD0 = Σ ( Cf · FF · Swet ) / S   +   extras (landing gear, antennas, leaks)

For each component:

  1. Compute Reynolds number Re = ρ V l / μ using the component's length l (chord for a wing, length for a fuselage).
  2. Compute Cf for turbulent flow from, say, Cf = 0.455 / (log₁₀ Re)^2.58 (a standard fit for 10⁶ to 10⁹).
  3. Estimate the form factor from empirical formulas. Two common ones:
    • Wing, tail: FF = 1 + 0.6/(x/c)ₘ · (t/c) + 100 (t/c)⁴, with (x/c)ₘ the location of maximum thickness.
    • Fuselage: FF = 1 + 60/f³ + f/400, with fineness ratio f = length/diameter.
  4. Multiply by the wetted area.

Add 5% to 10% for interference and leakage, and add the drag area of any items outside the pattern, such as fixed landing gear. The method gives CD0 within 10% to 20% when used by an experienced engineer with good inputs. For a conceptual design that is adequate; wind-tunnel tests refine it. The run below applies the recipe to a light aircraft.

Common misconceptions

"Drag depends only on frontal area." It also depends on the shape through CD, on whether the layer is laminar or turbulent, and on the surface roughness.

"A smooth surface always means less drag." For bluff bodies at the right Reynolds number, a rough surface can delay separation and reduce drag.

"Skin friction and form drag are separate things you can switch off independently." A streamlining change reduces form drag but adds wetted area (hence friction). The best shape balances both.

Try it

Python Component drag buildup for a light aircraft

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

JS Drag of different shapes at the same speed

Press Run (or Ctrl + Enter) to see the console output here.

No output.

Check your understanding

Quick check · 5 questions

of 5 answered You scored / 5 · perfect!

  1. 1. What is the main cause of the large drag of a bluff body?

    Separated flow leaves low pressure at the rear of the body while the front has high pressure, so the pressure difference pushes the body backward.
  2. 2. What happens at the drag crisis of a sphere?

    A turbulent layer stays attached longer, shrinking the wake, so form drag falls.
  3. 3. Wetted area is:

    Skin friction acts over every surface in contact with the flow.
  4. 4. Why does interference drag arise?

    Junctions disturb the flow, and fairings smooth that interaction.
  5. 5. In a component buildup, the drag area of a component is computed as:

    Friction coefficient times form factor times wetted area gives the equivalent flat plate area of the component.

Summary

  • Pressure (form) drag comes from a separated wake; streamlining keeps the flow attached.
  • Bluff bodies have CD of order 1 on frontal area; streamlined shapes of order 0.05.
  • The drag crisis lowers sphere and cylinder drag when the boundary layer turns turbulent.
  • CD0 ≈ Σ(Cf·FF·Swet)/S plus interference and extras.

Next: The drag polar