Skip to content
Tutorials Center
My learning

Topics

Lesson 46 of 49 · Projects and Practice

Practice problems with an answer checker

Twelve aerodynamics practice problems on wings, compressible flow, shocks, stability, dynamics and CFD, with a runnable checker that computes every answer.

Reading about aerodynamics is not the same as using it. These twelve problems cover Chapters 5 to 8 with a mix of short calculations and small decisions. Work each one on paper first, then run the checker at the bottom to compare your result. If you disagree, find out why: a unit slip, a missed square, or a misunderstanding of the physics.

Twelve tiles listing practice topics from aspect ratio to CFD basics, each with its key formula.
Twelve skills, one per tile. Each problem uses the formula shown.

What you will learn

  • To apply the key formulas of Chapters 5 to 8 to concrete numbers.
  • To choose the right tool for each question.
  • To check your answers against a runnable solution.

How to use this page

Use sea-level air (ρ = 1.225 kg/m³, T = 288.15 K, γ = 1.4, R = 287.05 J/(kg K)) unless a problem says otherwise, and g = 9.81 m/s². Give answers with sensible precision: three significant figures is plenty.

Wings and performance (Chapter 5)

  1. A wing has span 18 m and area 27 m². What is its aspect ratio?
  2. A wing with AR = 12 and e = 0.9 flies at CL = 0.6. Find the induced drag coefficient.
  3. An airplane of mass 1,200 kg has S = 16 m² and CLmax = 1.6. What is its stall speed at sea level?

Compressible flow (Chapter 6)

  1. At 11 km altitude the temperature is 216.65 K. What is the Mach number of an aircraft flying at 240 m/s?
  2. Static conditions are p = 50 kPa, T = 250 K at M = 0.8. Find the stagnation pressure and temperature.
  3. A normal shock stands in a Mach 2.5 stream. Find the Mach number behind it and the static pressure ratio p₂/p₁.
  4. A Mach 3 flow meets a 15° wedge. Find the weak oblique shock angle.
  5. Using Ackeret theory, find the lift coefficient of a flat plate at α = 3° and M = 2.5.

Stability and dynamics (Chapter 7)

  1. An airplane has a = 5.0 per radian and neutral point at 0.45 chord. With the CG at 0.32, find the static margin and Cm,α.
  2. An airplane has Cm0 = 0.04, Cm,α = −0.9 per radian, a = 5 per radian, CL0 = 0.15 and Cm,δe = −1.0 per radian. What elevator angle trims it at CL = 0.7?
  3. Estimate the phugoid period and damping ratio at V = 90 m/s with L/D = 15.

Computation (Chapter 8)

  1. (a) An explicit upwind scheme advects a wave at c = 340 m/s on a grid with Δx = 0.01 m. What is the largest stable time step? (b) For a flat plate of chord 2 m at 50 m/s (ν = 1.46 × 10⁻⁵ m²/s), estimate the first-cell height for y⁺ = 1 using C_f ≈ 0.026 Re^(−1/7).

Key terms

Dimensional check: confirming that both sides of an equation have the same units.

Limiting case: testing a formula at an extreme where the answer is known.

Significant figures: the digits that carry real information.

Try it

The checker below computes all twelve answers. Do the problems first, then run it. Each answer is labeled by problem number.

Python Answer checker

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. Which check catches the most mistakes before you run any code?

    A dimensional check catches missing squares and wrong conversions immediately.
  2. 2. An answer says the induced drag coefficient of a long wing is larger than that of a short wing at the same CL. What is wrong?

    A limiting-case check shows the result must be wrong.
  3. 3. Which formula would you use to find the Mach number behind a normal shock?

    That is the normal-shock relation for air.
  4. 4. A static margin of 13% chord means

    K = h_n − h = 0.13.

Summary

  • The twelve problems cover the main calculation skills of Chapters 5 to 8.
  • Do them by hand first; use the checker to learn from differences.
  • Units, limiting cases and orders of magnitude catch most errors.

Next: Glossary