Skip to content
Tutorials Center
My learning

Topics

Lesson 16 of 45 ยท Components and Footprints

Chapter 3 Review: Components and Footprints

Review preferred values, chip and IC packages, footprints and datasheets with a recap table, a one-picture summary and a ten-question quiz for chapter 3.

This chapter gave you the vocabulary and the habits of a careful parts person: use preferred values, know your package sizes, build and verify footprints and read datasheets with a pencil. They are not glamorous, but they prevent most board failures.

Four cards: passives, packages, footprints and datasheets, each with a small icon and three key reminders
Chapter 3 in one picture: passives, packages, footprints, datasheets.

Recap table

Topic Remember
E-series E6 (20 %), E12 (10 %), E24 (5 %); values spaced geometrically; E96 for 1 %
Resistors Choose value, tolerance, power (derate to 50 %), maximum voltage
Capacitors C0G stable, X7R general, avoid Y5V; DC bias loses capacitance; rating at least 2ร— the voltage
Chip sizes 0402 = 1.0ร—0.5, 0603 = 1.6ร—0.8, 0805 = 2.0ร—1.25, 1206 = 3.2ร—1.6 mm (imperial)
IC packages DIP 2.54 mm, SOIC 1.27 mm, QFN about 0.5 mm; pitch decides difficulty
Footprint Pads, mask, paste, silkscreen, courtyard; toe, heel, side extensions
Verify Compare with datasheet, print at 1:1, check pin 1 and polarity
Datasheet Absolute max, operating conditions, electrical table, pinout, package, application circuit

Lessons in this chapter

Check your understanding

Quick check ยท 10 questions

of 10 answered You scored / 10 ยท perfect!

  1. 1. Which E-series has the tightest tolerance?

    E96 values are about 1 % apart, so parts are about 1 % accurate.
  2. 2. A resistor carries 50 mA and has 100 ฮฉ. Its dissipation is

    P = IยฒR = 0.05ยฒ ร— 100 = 0.25 W, so a 0603 (1/10 W) is far too small.
  3. 3. Which dielectric would you choose for a precise RF filter capacitor of 10 pF?

    C0G is stable with temperature and bias.
  4. 4. Why use a capacitor rated for more than twice the rail voltage?

    High bias fraction reduces ceramic capacitance and reduces margin.
  5. 5. What size is an imperial 0805 chip?

    0805 imperial is 0.08 in ร— 0.05 in, i.e. 2.0 ร— 1.25 mm.
  6. 6. Which IC package is a through-hole part with 2.54 mm pitch?

    DIP is through-hole; QFN and BGA are surface-mount.
  7. 7. Silkscreen on a pad does what?

    Keep ink off the pads.
  8. 8. What does the courtyard do?

    DRC warns about overlapping courtyards.
  9. 9. Which is guaranteed by the datasheet?

    Only min and max are guaranteed.
  10. 10. A regulator drops 5 V to 3.3 V at 400 mA. Heat dissipated?

    (5 โˆ’ 3.3) ร— 0.4 = 0.68 W.

Summary

  • Use preferred values, derate ratings and watch capacitor behavior.
  • Know your package codes and pitches; imperial and metric names differ.
  • Build, check and print footprints; verify every new one.
  • Read the six datasheet sections before using a part.

Next: Chapter 4 Overview: Layout and Routing