Machine Design Tutorial
Learn Machine Design step by step: 46 lessons in 9 chapters with examples, quizzes, diagrams and practice.
Start learning →
of lessons completed
Getting Started
- Course Map: How to Study Machine Design Start here. See who the Machine Design course is for, what you need first, how the nine chapters fit together and how to study them with worked examples and simulations.
- What Is Machine Design? Learn what machine designers actually decide, how design differs from analysis, the families of machine elements and why every design is a trade-off between strength, weight and cost.
- Units, Calculations and Materials Master the SI unit habits of machine design, convert power to torque, read stress-strain curves and compare steel, aluminum, titanium and cast iron by strength, stiffness and weight.
- Chapter 1 Review: Getting Started Review chapter 1 of Machine Design: the design loop, consistent SI units, torque from power, stress-strain curves and material comparison, with a ten-question quiz.
Design Process and Loads
- Design Process and Loads: The Big Picture Chapter 2 overview: the iterative design process, the kinds of loads a machine part sees, stress concentration and how safety factors and reliability turn uncertainty into numbers.
- The Design Process and Requirements Learn how engineers turn a vague need into a requirement list, generate concepts, iterate on sizes with calculations and document the result so the design can be built and trusted.
- Loads and Load Paths Classify machine loads as static, cyclic, impact or thermal, compute gear and impact forces, find stress amplitude and mean, and trace a force through a machine to the ground.
- Stress Concentration Understand why stress piles up at holes, fillets and notches, compute Kt for a plate with a hole, learn when to apply it to static and fatigue loading and how to design it away.
- Safety Factors and Reliability Learn what a factor of safety is, how to choose a design factor, why scatter in stress and strength creates failure probability, and how part reliabilities combine in a system.
- Chapter 2 Review: Design Process and Loads Review chapter 2 of Machine Design: the design loop, load types and cycles, gear and impact forces, stress concentration Kt and Kf, safety factors and reliability, with a ten-question quiz.
Fatigue and Failure
- Fatigue and Failure: The Big Picture Chapter 3 overview: why parts fail by yielding, fracture, fatigue and wear, how failure theories predict yielding under combined stress, and how fatigue life is estimated.
- Static Failure Theories: Von Mises, Tresca and Brittle Criteria Combine bending, torsion and axial stresses into one equivalent stress with the von Mises and Tresca criteria, find principal stresses, and treat brittle materials with Coulomb-Mohr.
- Fatigue and the S-N Curve See how fatigue cracks start, grow and snap a part, read the S-N curve, estimate the endurance limit and finite life with Basquin's equation, and add damage with Miner's rule.
- Endurance Limit and the Marin Factors Correct the laboratory endurance limit for surface finish, size, load type, temperature and reliability with the Marin equation, with worked values for a steel shaft and a calculator.
- Fluctuating Stress and the Goodman Line Check parts under both a steady mean stress and an alternating stress using the Goodman, Soderberg, Gerber and Langer criteria, with worked factors of safety and a bending-plus-torsion shaft.
- Chapter 3 Review: Fatigue and Failure Review chapter 3 of Machine Design: von Mises and Tresca criteria, fatigue crack stages, the S-N curve, Marin factors and the Goodman line, with a combined shaft check and a ten-question quiz.
Shafts and Fasteners
- Shafts and Fasteners: The Big Picture Chapter 4 overview: how rotating shafts, keys, critical speed and bolted joints work together, why bending and fatigue size a shaft, and why preload keeps a joint tight.
- Shaft Design for Bending, Torque and Fatigue Design a rotating shaft step by step: reactions, shear and moment diagrams, stress concentration, the DE-Goodman diameter formula, a yield check and deflection limits, with a worked example.
- Keys, Splines and Critical Speed Size parallel keys for shear and bearing stress, compare keys, splines and press fits, and estimate the critical speed of a shaft so it never runs in resonance.
- Bolted Joints and Preload Understand why a bolt needs preload, compute bolt and member stiffness and the joint constant C, find bolt and clamp forces under external load, and check proof, separation and fatigue.
- Chapter 4 Review: Shafts and Fasteners Review chapter 4 of Machine Design: DE-Goodman shaft sizing, key shear and bearing, critical speed, bolt preload and joint constant, with a combined problem and a ten-question quiz.
Gears
- Chapter 5 overview: gears A map of the gears chapter: why machines use gears, the four main gear families, and how geometry, tooth forces and stress checks fit together.
- Gear geometry and ratios Learn the involute tooth, module, pitch diameter, pressure angle, contact ratio and minimum tooth count, then size a gear pair and build a gear train.
- Tooth forces and bending strength Turn power into tooth force, then check a spur gear for bending with the Lewis equation and for surface fatigue with Hertz contact stress, with worked numbers.
- Helical, bevel and worm gears Compare helical, bevel and worm gears: thrust forces, cone angles, lead angle, self-locking and efficiency, with worked force calculations.
- Chapter 5 review: gears Review the gears chapter with a one-page picture, a recap table of every formula, a pair-selection search and ten mixed check questions.
Bearings and Springs
- Chapter 6 overview: bearings and springs A map of the bearings and springs chapter: rolling bearings and their L10 life, journal bearings and oil films, and helical springs for load and energy storage.
- Rolling bearing life and selection Choose a ball or roller bearing from a catalog: basic load rating C, the L10 life formula, equivalent dynamic load, reliability factors and a worked selection.
- Journal bearings and lubrication Understand how a journal bearing carries a shaft on an oil film: the wedge effect, lubrication regimes, the Stribeck curve, Petroff friction and a worked power-loss example.
- Helical compression springs Design a helical compression spring: spring rate k = G d^4 / (8 D^3 Na), shear stress with correction factors, end types, solid length, buckling and surge, with a worked design.
- Chapter 6 review: bearings and springs Review the bearings and springs chapter with a one-page picture, a recap table of formulas, a bearing selector from a small catalog and ten mixed questions.
Brakes, Clutches and Belts
- Chapter 7 overview: brakes, clutches and belts A map of chapter 7: how clutches, brakes and belts use friction to transmit torque, why heat limits them, and how the lessons fit together.
- Disc clutches and disc brakes Calculate the torque capacity of disc clutches and brakes with the uniform pressure and uniform wear models, find the best lining radii, and estimate engagement heat.
- Drum brakes and band brakes Design block (shoe) brakes and band brakes: derive the capstan equation F1/F2 = e^(mu theta), find torque, lever force, self-energizing and self-locking, with worked numbers.
- Belt drives Design flat and V-belt drives: belt length, wrap angle, tight and slack tensions with centrifugal effect, the V-belt wedge, shaft load and the speed for maximum power.
- Chapter 7 review: brakes, clutches and belts Review chapter 7: torque of disc clutches and brakes, band and shoe brakes, the capstan equation, belt tensions and the heat check, with ten mixed questions.
Design Projects
- Chapter 8 overview: design projects Learn the loop that every machine design follows (requirements, concept, calculation, checks, iteration) and preview three projects: a gear reducer, its bearings and a clutch.
- Project: a spur gear reducer Design a single-stage spur gear reducer step by step: requirements, tooth counts and module search, bending and contact checks, safety factors and a final specification.
- Project: shafts and bearings for the reducer Continue the reducer project: find bearing reactions and bending moments from the gear forces, check the shaft for fatigue, and select deep groove bearings for 20,000 hours.
- Project: a spring-loaded disc clutch Design a dry single-plate clutch for a 7.5 kW motor: friction torque capacity, lining pressure, engagement heat, then the ring of compression springs that provides the clamp force.
- Chapter 8 review: design projects Review the three design projects: the gear reducer, its shafts and bearings, and the spring-loaded clutch, with a results table, a scaling study and ten mixed questions.
Projects and Practice
- Practice problems: gears, bearings, springs and friction devices Thirteen practice problems on gears, bearings, springs, clutches, brakes and belts, with hints, a worked-answer script and an interactive answer checker.
- Capstone: a complete conveyor drive Put it all together: design a motor, V-belt, spur reducer, drum shaft bearings and emergency band brake for a belt conveyor, with every step calculated and checked.
- Glossary of machine design terms Forty clear definitions for gears, bearings, springs, clutches, brakes, belts and design practice, with formulas and a flashcard drill to learn them.
- Cheat sheet: chapters 5 to 8 in one page A one-page recap of the key formulas and typical values for gears, bearings, springs, clutches, brakes, belts and design checks, with a reusable Python formula library.
- Further study: where to go after machine design A roadmap for what to learn next after gears, bearings, springs and friction devices: fatigue, vibration, standards, materials, simulation and the related tracks on this site.