Skip to content
Tutorials Center
My learning

Topics

RF Engineering and Antennas Tutorial

Learn RF Engineering and Antennas step by step: 46 lessons in 9 chapters with examples, quizzes, diagrams and practice.

Start learning →

of lessons completed

Getting Started

  1. 1 Course Map: How This RF and Antenna Course Works Start here: who the RF engineering and antennas course is for, what you need to know, how the nine chapters fit together and how to study with the live tools.
  2. 2 The Radio Spectrum and Frequency Bands Learn how frequency and wavelength are linked, how the ITU and IEEE name the RF bands, and why wavelength decides whether a circuit is lumped or distributed.
  3. 3 Decibels, dBm and Power Levels Master the decibel for RF work: power and voltage ratios, dBm, dBW, dBc and dBi, the 3 dB rule, signal chains and the mistakes that trip up beginners.
  4. 4 Noise and the Thermal Floor Understand thermal noise (kTB, -174 dBm/Hz), noise figure, noise temperature and how they set receiver sensitivity, with worked examples and a noise simulation.
  5. 5 Chapter 1 Review: Getting Started Review chapter 1 of the RF course: wavelength and bands, decibels and dBm, thermal noise and sensitivity, with a recap table, practice problems and a ten-question quiz.

Waves and Transmission Lines

  1. 6 Chapter 2 Overview: Waves on Cables and Transmission Lines A map of chapter 2: why a cable needs wave theory once it is long compared with the wavelength, and what you will learn about Z0, reflections, VSWR and impedance transformation.
  2. 7 The Transmission Line Model: Z0, Velocity and Loss Build the transmission line from tiny R, L, G and C elements, derive Z0 and velocity, and compute coax impedance from its dimensions with a live calculator.
  3. 8 Reflection Coefficient, VSWR and Return Loss Learn how a mismatched load reflects part of the wave, how to compute the reflection coefficient, VSWR, return loss and mismatch loss, and how standing waves form.
  4. 9 Impedance Along a Line: Stubs and Quarter-Wave Transformers Learn how the impedance seen at the input of a line depends on its length, how shorted and open stubs act as inductors and capacitors, and how a quarter-wave section matches two resistances.
  5. 10 Chapter 2 Review: Waves and Transmission Lines Review chapter 2: the line model, characteristic impedance, reflection coefficient, VSWR, input impedance, stubs and quarter-wave transformers, with practice code and a ten-question quiz.

Smith Chart and Matching

  1. 11 Chapter 3 Overview: The Smith Chart and Impedance Matching A map of chapter 3: what the Smith chart shows, why RF engineers still use it, and how you will use it to read impedances, move along lines and design matching networks.
  2. 12 Smith Chart Basics: Reading Impedance and Reflection Learn how the Smith chart is built from the reflection coefficient, how to read resistance and reactance circles, VSWR circles and the admittance chart, with a live chart.
  3. 13 Lumped-Element Matching: Designing L-Networks Design an L-match from two parts: pick the topology, compute Q, the series reactance and the shunt susceptance, choose low-pass or high-pass, and check the bandwidth.
  4. 14 Stub and Quarter-Wave Matching Design single-stub and quarter-wave matches step by step: stub position and length from the admittance equation, numeric worked examples and a designer you can run.
  5. 15 Chapter 3 Review: Smith Chart and Matching Review chapter 3: reading the Smith chart, moving along lines, L-network design, single-stub and quarter-wave matching, with practice problems and a ten-question quiz.

S-Parameters and Microwave Networks

  1. 16 Chapter 4 Overview: S-Parameters and Microwave Networks A map of chapter 4: why microwave engineers use S-parameters instead of voltages and currents, what a vector network analyzer measures, and how two-port networks are described.
  2. 17 S-Parameter Basics: Definitions, Properties and dB Learn what S11, S21, S12 and S22 mean, how they come from incident and reflected waves, how to read them in dB, their properties and how reference planes shift them.
  3. 18 ABCD Matrices and Cascaded Networks Learn to describe series, shunt and line sections with ABCD matrices, cascade them by multiplication, convert to S-parameters and analyze a lowpass filter.
  4. 19 Passive Microwave Components: Attenuators, Dividers and Couplers Learn how pi and T attenuators, Wilkinson power dividers and directional couplers work, with design equations, S-parameters and calculators for pads and coupling.
  5. 20 Chapter 4 Review: S-Parameters and Microwave Networks Review chapter 4: S-parameter definitions and properties, ABCD matrices and cascading, pi and T attenuators, Wilkinson dividers and couplers, with practice code and a quiz.

Amplifiers and Mixers

  1. 21 Amplifiers and Mixers: The Big Picture See how low noise amplifiers, mixers and filters fit together in a receiver, and what noise, linearity and frequency conversion each decide.
  2. 22 Noise Figure and the Cascade Learn thermal noise, noise figure, noise temperature and the Friis cascade formula, and see why a low noise amplifier must come first in a receiver.
  3. 23 Linearity and Stability Understand gain compression, the 1 dB point, third-order intermodulation, intercept points, dynamic range and the Rollett stability factor of RF amplifiers.
  4. 24 Mixers and Frequency Conversion Learn how a mixer multiplies RF by a local oscillator, creates sum and difference tones, why the image frequency is a problem, and how superheterodyne receivers work.
  5. 25 Chapter Review: Amplifiers and Mixers Review gain in dB, noise figure and the Friis cascade, P1dB and IP3, stability and mixer frequency planning with a recap table and a ten question quiz.

Antenna Fundamentals

  1. 26 Antenna Fundamentals: The Big Picture Preview the core antenna ideas: radiation patterns, directivity and gain, impedance and efficiency, polarization, effective aperture and the Friis equation.
  2. 27 Pattern, Gain and Directivity Learn to read radiation patterns, measure beamwidth and sidelobes, compute directivity from the pattern, and tell directivity from gain and dBi from dBd.
  3. 28 Impedance, Efficiency and Polarization Understand radiation resistance, reflection coefficient, VSWR and mismatch loss, antenna bandwidth and efficiency, and how polarization mismatch costs decibels.
  4. 29 Aperture and the Friis Equation Learn effective aperture, EIRP and the Friis transmission equation, and calculate received power for a free-space link in linear form and in decibels.
  5. 30 Chapter Review: Antenna Fundamentals Review radiation patterns, directivity and gain, impedance and VSWR, polarization loss, effective aperture and the Friis equation with a recap table and ten questions.

Antenna Types and Arrays

  1. 31 Antenna Types and Arrays: The Big Picture A tour of the main antenna families: wire antennas, patches, horns, dishes and phased arrays, with the idea that links them: aperture size measured in wavelengths.
  2. 32 Wire and Patch Antennas Design dipoles, monopoles, Yagi-Uda antennas and rectangular microstrip patch antennas using practical length rules and the transmission-line patch equations.
  3. 33 Horns and Dishes: Aperture Antennas Learn how aperture antennas work, compute horn and parabolic reflector gain and beamwidth, and understand aperture efficiency, feed illumination and blockage.
  4. 34 Arrays and Beamforming Learn the array factor of a uniform linear array, how phase steers the beam, why spacing creates grating lobes, how tapering lowers sidelobes, and how beamforming works.
  5. 35 Chapter Review: Antenna Types and Arrays Review dipoles, monopoles, Yagi-Uda antennas, patches, horns, dishes and phased arrays with a recap table, typical gains and a ten question quiz.

Propagation and Link Budgets

  1. 36 Propagation and Link Budgets: The Big Picture See how radio waves travel by ground wave, sky wave and line of sight, and how a link budget adds gains and losses to predict whether a signal arrives.
  2. 37 Free Space, Fresnel Zones and the Radio Horizon Calculate free-space path loss, Fresnel zone radius and clearance, the radio horizon with the 4/3 earth model, and estimate atmospheric and rain losses on microwave links.
  3. 38 Building a Link Budget Build a complete RF link budget: transmit power and EIRP, path loss, receiver noise floor, SNR, Eb/N0 and link margin, with a worked Wi-Fi example and a range calculator.
  4. 39 Fading and Multipath Understand multipath, the two-ray ground model, Rayleigh and Rician fading, Doppler and delay spread, and how fade margin and diversity keep a radio link reliable.
  5. 40 Chapter Review: Propagation and Link Budgets Review free-space loss, Fresnel clearance, the radio horizon, the link budget equation, noise floor, Eb/N0 and fading margins with a recap table and ten questions.

Projects and Practice

  1. 41 Project: A 2 km Point-to-Point Link Budget Design a 2 km, 5.8 GHz point-to-point link step by step: path loss, EIRP, received power, noise floor, SNR, Fresnel clearance and fade margin, then explore what-if cases.
  2. 42 Project: Design a 2.45 GHz Patch Antenna Design a rectangular microstrip patch for 2.45 GHz on FR-4: width, effective permittivity, length, inset feed and a model of its return loss and bandwidth, step by step.
  3. 43 Practice: An RF Problem Set Ten RF and antenna practice problems covering dBm, cascaded noise figure, intermodulation, mixers, EIRP, path loss, Fresnel zones and fading, with worked solutions you can run.
  4. 44 Glossary of RF and Antenna Terms A glossary of thirty RF and antenna terms from dB and noise figure to P1dB, IP3, VSWR, directivity, EIRP, Fresnel zones and fade margin, with a searchable lookup tool.
  5. 45 RF and Antennas Cheat Sheet One-page recap of the key RF and antenna formulas: decibels, matching, noise, linearity, antennas and link budgets, with a calculator for the most used ones.
  6. 46 Further Study: Where to Go After RF A roadmap from RF and antennas to signals and systems, communication systems, semiconductor devices, analog electronics, PCB design and power electronics.