Skip to content
Tutorials Center
My learning

Topics

Lesson 42 of 47 · Projects and Practice

Practice set: rigid bodies and vibrations

Ten worked-answer practice problems on rotation, relative velocity, rolling, moment of inertia, energy and vibration, with a solution checker you can run.

Reading about dynamics is not the same as solving problems. This practice set has ten problems that span chapters 5 to 7. Try each one on paper first, using the five-step routine: sketch, choose, write, solve, check. Then compare with the answers and run the calculator at the end.

Five numbered cards: sketch, choose, write, solve, check
The five-step routine: every dynamics problem fits it.

What you will learn

  • Apply the tools of chapters 5 to 7 to mixed problems.
  • Pick a method from what the question asks.
  • Check answers with limits and units.
  • Use a program to verify hand calculations.

Key terms

Knowns and unknowns: list them before choosing equations.

Constraint: a geometric relation (rolling, pin, rope) that links motions.

Sanity check: a quick test, such as a limiting case or a unit check, that catches gross errors.

The routine

  1. Sketch the system, mark positive directions, add all forces.
  2. Choose the method: forces and moments for accelerations and reactions, energy for speed after a distance, momentum for impacts, relative velocity or IC for linkages.
  3. Write the equations and constraints; count unknowns.
  4. Solve with symbols first, then numbers, carrying units.
  5. Check: signs, size, limiting cases.

Problems

Use g = 9.81 m/s².

1. Braking flywheel. A flywheel turning at 1800 rpm is brought to rest uniformly in 12 s. Find the angular deceleration and the number of turns.

2. Belt drive. A pulley of radius 0.08 m turns at 150 rad/s and drives a pulley of radius 0.20 m with a belt that does not slip. Find the angular speed of the large pulley and the belt speed.

3. Sliding bar. A bar AB of length 0.6 m has end A on a floor and end B on a wall. When it makes 30° with the floor, A moves away from the wall at 2 m/s. Find ω of the bar and the speed of B.

4. Rolling wheel. A wheel of radius 0.25 m rolls without slipping with v_G = 5 m/s constant. Find ω, the speed of the top point and the acceleration of the contact point.

5. Composite inertia. A uniform rod (2 kg, 0.9 m) has a 1 kg point mass attached at one end. Find I about the other end.

6. Falling rod. A uniform rod (1.5 kg, 0.8 m) pinned at one end is released from horizontal. Find α at release and ω when the rod is vertical.

7. Damped system. A machine of 25 kg sits on a spring of 10 kN/m with a damper of 250 N·s/m. Find ωn, ζ and ωd.

8. Resonance. The same system is driven by F₀ = 100 N at its natural frequency. Estimate the steady amplitude.

9. Hollow sphere. A thin hollow sphere rolls without slipping down a 20° incline. Find its acceleration.

10. Rolling cylinder. A solid cylinder rolls from rest through a vertical drop of 2.4 m. Find its speed at the bottom.

Answers

# Answer Key step
1 α = −15.7 rad/s²; 180 turns ω₀ = 188.5 rad/s; average speed 900 rpm × 12 s
2 ω₂ = 60 rad/s; belt 12 m/s ω₁r₁ = ω₂r₂
3 ω = 6.67 rad/s; v_B = 3.46 m/s IC: ω = v_A/(L sin30°), v_B = ω L cos30°
4 ω = 20 rad/s; top 10 m/s; a = 100 m/s² upward a_C = ω²R toward the center
5 1.35 kg·m² mL²/3 + m_p L² = 0.54 + 0.81
6 α = 18.4 rad/s²; ω = 6.07 rad/s α = 3g/2L; ω = √(3g/L)
7 ωn = 20 rad/s; ζ = 0.25; ωd = 19.4 rad/s c_cr = 2√(km) = 1000 N·s/m
8 X = 20 mm δ_st = 10 mm, X = δ_st/(2ζ)
9 a = 2.01 m/s² a = g sinθ/(1 + 2/3)
10 v = 5.60 m/s v = √(4gh/3)

If a result surprises you, test it with a limiting case. In problem 3, as the bar approaches the wall (angle near 90°), v_B should tend to zero: v_B = v_A / tanφ does.

Common misconceptions

Using rpm in v = ωr. Convert to rad/s first.

Choosing the wrong method. Energy cannot give a reaction force at an instant; relative velocity cannot give accelerations without α.

Forgetting the second part of a. On a rotating body, a_n = ω²r exists even when α = 0.

Try it

This program solves all ten problems from the formulas, so you can compare it with your own answers.

Python Solution checker for the ten problems

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The second program builds a fresh random flywheel problem every time you change the seed, and prints the answer, so you can keep practicing the same skill.

Python Random flywheel problem generator

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Check your understanding

Quick check · 5 questions

of 5 answered You scored / 5 · perfect!

  1. 1. A wheel rolls at constant speed. Which point has the largest speed?

    The top is farthest from the IC (2R), so it moves at 2v.
  2. 2. What is I of a 4 kg disk of radius 0.5 m about its center?

    I = ½mR² = ½ × 4 × 0.25 = 0.5 kg·m².
  3. 3. For which question is energy the best method?

    Energy links speed to the change in height without needing accelerations.
  4. 4. A system has ζ = 0.05 and is driven at resonance. The magnification is:

    M = 1/(2ζ) = 10.
  5. 5. In sanity-checking, which test is most useful for a formula for a falling rod?

    Limiting cases catch structural mistakes that unit checks miss.

Summary

  • Sketch, choose, write, solve, check: the same routine for every problem.
  • The question decides the method: instant (forces), speed after a distance (energy), collision (momentum), linkage (relative velocity, IC).
  • Code is a fast way to verify hand work and to explore variations.

Next: Project: vibration isolation for a machine