Skip to content
Tutorials Center
My learning

Topics

Lesson 43 of 46 ยท Projects and Practice

Practice problems with worked answers

Eight worked fluid dynamics problems covering Couette and Poiseuille flow, boundary layers, Kolmogorov scales, tsunami speed, convection, CFL limits and drag, with a checker.

Reading about fluid dynamics is not the same as using it. This lesson gives eight short problems, one for each big idea of the course. Try each on paper first, write down the formula you plan to use and its units, and only then read the solution. A program at the end checks all eight answers.

A grid of eight numbered problem cards with difficulty bars
Eight problems: one from each chapter of the course.

What you will learn

  • How to choose the right formula for a physical situation.
  • How to carry units through a calculation and sanity-check an answer.
  • How to check that a formula's assumptions hold (for example, laminar flow).
  • How to confirm your hand results with a short program.

Key terms

  • Sanity check: asking whether a result is plausible (right size, right units) before trusting it.
  • Assumption check: verifying the conditions of a formula, such as Re < 2,300 for laminar pipe flow.
  • Order of magnitude: the power of ten of a quantity.

The problems

Use these property values unless the problem says otherwise: air ฯ = 1.2 kg/mยณ, ฮฝ = 1.5ร—10โปโต mยฒ/s; water ฯ = 1000 kg/mยณ, ฮฝ = 10โปโถ mยฒ/s, ฮผ = 10โปยณ Pa s; g = 9.81 m/sยฒ.

Problem 1 (Couette flow). A journal bearing has an oil film 0.1 mm thick between a fixed surface and a surface moving at 2 m/s. The oil has ฮผ = 0.05 Pa s. Find the shear stress, and the friction force on 0.2 mยฒ of surface.

Solution. The profile is linear, so ฯ„ = ฮผ U/h = 0.05 ร— 2 / 10โปโด = 1,000 Pa. The force is F = ฯ„ A = 1,000 ร— 0.2 = 200 N.

Problem 2 (Poiseuille flow). Water flows through a tube of diameter 4 mm and length 1 m under a pressure drop of 1 kPa. Find the flow rate and verify that the flow is laminar. What is the wall shear stress?

Solution. G = 1,000 Pa/m, R = 2 mm. Q = ฯ€ G Rโด/(8ฮผ) = ฯ€ ร— 1000 ร— (2ร—10โปยณ)โด / (8 ร— 10โปยณ) = 6.3ร—10โปโถ mยณ/s (6.3 mL/s). The mean velocity is GRยฒ/(8ฮผ) = 0.5 m/s, so Re = 0.5 ร— 0.004/10โปโถ = 2,000, below 2,300: laminar, so the formula is valid (but close to the limit). Wall shear: ฯ„w = G R/2 = 1.0 Pa.

Problem 3 (Boundary layer). Air at 5 m/s flows along a smooth flat plate 0.4 m long. Find the boundary-layer thickness at the trailing edge and the friction drag per meter of width on one side.

Solution. Re_L = 5 ร— 0.4 / (1.5ร—10โปโต) = 1.33ร—10โต, laminar. ฮด = 4.91 L/โˆšRe_L = 4.91 ร— 0.4/365 = 5.4 mm. C_D = 1.328/โˆšRe_L = 3.6ร—10โปยณ. D = C_D ร— ยฝฯUยฒ ร— L = 3.6ร—10โปยณ ร— 15 ร— 0.4 = 0.022 N/m.

Problem 4 (Kolmogorov scale). In an atmospheric boundary layer the dissipation rate is ฮต = 0.01 mยฒ/sยณ. Find the Kolmogorov length and time.

Solution. ฮท = (ฮฝยณ/ฮต)^(1/4) = ((1.5ร—10โปโต)ยณ/0.01)^(1/4) = 0.76 mm. ฯ„_ฮท = (ฮฝ/ฮต)^(1/2) = (1.5ร—10โปยณ)^(1/2) = 0.039 s.

Problem 5 (Tsunami). A tsunami crosses a shelf 200 m deep. Find its speed, and the time to travel 100 km at that depth.

Solution. c = โˆš(g h) = โˆš(9.81 ร— 200) = 44 m/s. t = 100,000/44.3 = 2,260 s โ‰ˆ 38 min.

Problem 6 (Convection). A layer of water 1 cm deep between two rigid plates is heated from below with a temperature difference of 1 K. Use ฮฑ = 2.1ร—10โปโด 1/K, ฮบ = 1.4ร—10โปโท mยฒ/s. Does convection start?

Solution. Ra = g ฮฑ ฮ”T dยณ/(ฮฝ ฮบ) = 9.81 ร— 2.1ร—10โปโด ร— 1 ร— 10โปโถ / (10โปโถ ร— 1.4ร—10โปโท) โ‰ˆ 1.5ร—10โด, far above Ra_c = 1708. Yes, convection starts.

Problem 7 (CFL limit). A CFD code uses explicit time stepping with cells 1 mm wide and a velocity of 2 m/s in air. Find the largest stable time step from the advection and diffusion limits.

Solution. Advection: ฮ”t โ‰ค ฮ”x/U = 10โปยณ/2 = 0.5 ms. Diffusion (2D): ฮ”t โ‰ค ฮ”xยฒ/(4ฮฝ) = 10โปโถ/(6ร—10โปโต) = 17 ms. The advection limit, 0.5 ms, controls.

Problem 8 (Drag). A smooth sphere of diameter 0.1 m moves through air at 10 m/s. Estimate the drag force. (Take C_D โ‰ˆ 0.47.)

Solution. Re = 10 ร— 0.1/(1.5ร—10โปโต) = 6.7ร—10โด, in the subcritical range where C_D โ‰ˆ 0.47. A = ฯ€ (0.05)ยฒ = 7.85ร—10โปยณ mยฒ. F = ยฝ ฯ Uยฒ C_D A = 0.5 ร— 1.2 ร— 100 ร— 0.47 ร— 7.85ร—10โปยณ = 0.22 N.

Try it

Python Check all eight answers

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

JS Create your own variations

Press Run (or Ctrl + Enter) to see the console output here.

No output.

Common misconceptions

  • "If the formula gives a number, the number is right." Always check the assumptions: Re below 2,300 for Q = ฯ€GRโด/8ฮผ; Re_x below about 5ร—10โต for the Blasius layer.
  • "Units are optional in intermediate steps." Most arithmetic mistakes in fluid problems are unit mistakes, such as millimeters used as meters.

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. A flow has Re = 2,000 in a pipe. Which formula for the friction factor applies?

    Below about 2,300 the flow is laminar and f = 64/Re.
  2. 2. Which limit controls the explicit time step in Problem 7?

    The stable time step is the smaller of the two limits, which is the advection limit here.
  3. 3. A tsunami is 4 times faster after the depth increases by what factor (linear shallow-water theory)?

    c = โˆš(g h), so a factor 4 in speed needs a factor 16 in depth.
  4. 4. What is the first thing to do before using Q = ฯ€GRโด/(8ฮผ)?

    The formula is exact only for laminar flow; check Re afterward.

Summary

  • Pick the formula, check its assumptions, carry units, and sanity-check the answer.
  • The eight problems cover Couette and Poiseuille flow, boundary layers, Kolmogorov scales, shallow-water waves, convection, CFL limits and drag.
  • A short program confirms hand results and lets you explore variations.

Next: Glossary