Skip to content
Tutorials Center
My learning

Topics

Lesson 16 of 39 · Reaction Rates

Rate Laws and Reaction Order

Write rate laws, find reaction orders and the rate constant k from initial-rate data, and work out the units of k for zero-, first- and second-order reactions.

A rate law connects the rate of a reaction to the concentrations of the reactants. With a rate law, you can predict how fast a reaction goes in any mixture. The rate law cannot be read off the balanced equation. It must be found by experiment.

The general form

For a reaction with reactants A and B, the rate law usually looks like

rate = k [A]^m [B]^n

  • k is the rate constant. It is specific to the reaction and depends on temperature, but not on concentration.
  • m and n are the reaction orders with respect to A and B. They are usually small integers (0, 1, 2), sometimes fractions.
  • The overall order is m + n.

The orders are not the coefficients of the balanced equation, except by coincidence (or when the equation describes a single elementary step; see Mechanisms and Catalysts).

What the order means

  • Zero order in A: changing [A] does not change the rate.
  • First order in A: doubling [A] doubles the rate.
  • Second order in A: doubling [A] quadruples the rate (2² = 4).

In general, if you multiply [A] by a factor f while the others stay fixed, the rate changes by the factor f^m.

Units of k

The units of k make the units of the rate law work out to M/s. If the overall order is p, the units of k are M^(1−p) s⁻¹.

Overall order Rate law Units of k
0 rate = k M/s
1 rate = k[A] s⁻¹
2 rate = k[A]² M⁻¹ s⁻¹ (L mol⁻¹ s⁻¹)
3 rate = k[A]²[B] M⁻² s⁻¹

The units of k often tell you the order of a reaction at a glance.

The method of initial rates

Run the reaction several times with different starting concentrations and measure the initial rate each time. Then compare experiments in which only one concentration changes.

The numbers below are an illustrative data set (made up for practice):

Experiment [A] (M) [B] (M) Initial rate (M/s)
1 0.10 0.10 2.0 × 10⁻³
2 0.20 0.10 8.0 × 10⁻³
3 0.10 0.20 4.0 × 10⁻³

Order in A: compare experiments 1 and 2. [A] doubles, [B] fixed. The rate quadruples (8.0/2.0 = 4), so 2^m = 4 and m = 2.

Order in B: compare experiments 1 and 3. [B] doubles, [A] fixed. The rate doubles, so 2^n = 2 and n = 1.

Rate law: rate = k [A]² [B], overall order 3.

Find k using experiment 1: k = rate / ([A]²[B]) = 2.0×10⁻³ / (0.10² × 0.10) = 2.0 × 10⁻³ / 1.0×10⁻³ = 2.0 M⁻² s⁻¹.

Python Find orders and k from initial rates

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Using a rate law

Once you know the rate law and k, you can predict rates for any mixture.

For rate = k[A]²[B] with k = 2.0 M⁻² s⁻¹: if [A] = 0.30 M and [B] = 0.050 M, then

rate = 2.0 × (0.30)² × 0.050 = 2.0 × 0.09 × 0.050 = 9.0 × 10⁻³ M/s.

Python Predict rates and see the effect of doubling

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Reactions with gases

For gases, concentrations can be replaced by partial pressures, and the constant is then a different (but related) k. Keep to one or the other within a problem.

Common mistakes

  • Reading orders from coefficients. Only experiment (or the slowest elementary step) tells you the order.
  • Forgetting to hold the other concentrations constant when comparing experiments. If two things change at once, use the full ratio of rates.
  • Wrong units of k. Check them against the overall order.

When the numbers are not clean doublings, take logarithms: m = ln(rate₂/rate₁) / ln([A]₂/[A]₁). Round to the nearest simple number if the data are experimental.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. A reaction is second order in A. If [A] triples, the rate

    Rate ∝ [A]². Tripling [A] multiplies the rate by 3² = 9.
  2. 2. The rate constant of a reaction has units of s⁻¹. The overall order is

    Units M^(1−p) s⁻¹ equal s⁻¹ when 1 − p = 0, so p = 1.
  3. 3. For 2 NO + O₂ → 2 NO₂, the experimental rate law is rate = k[NO]²[O₂]. The overall order is

    2 + 1 = 3. The coefficients happen to match here, but you always need experimental data to know.
  4. 4. Doubling [B] doubles the rate, and doubling [A] has no effect. The rate law is

    First order in B, zero order in A (it drops out of the rate law).

Summary

  • A rate law rate = k[A]^m[B]^n is found by experiment, not from the balanced equation.
  • The orders m, n tell how the rate responds to each concentration; the sum is the overall order.
  • The method of initial rates compares experiments with one concentration changed at a time.
  • k depends on temperature; its units are M^(1−p) s⁻¹ for overall order p.
  • With the rate law and k you can predict the rate for any concentrations.

Next: Integrated Rate Laws and Half-Life