Skip to content
Tutorials Center
My learning

Topics

Lesson 29 of 39 · Acids and Bases

Acid-Base Titrations and Titration Curves

Work out unknown concentrations with titrations, calculate titration curves for strong and weak acids, and choose indicators for the equivalence point.

A titration is a careful way to find the concentration of a solution. You add a solution of known concentration (the titrant) from a burette to a measured volume of the unknown (the analyte) until the reaction is exactly complete. That moment is the equivalence point.

The basic calculation

For a 1:1 reaction such as HCl + NaOH → NaCl + H2O, at equivalence the moles of acid equal the moles of base. Moles are n = c × V (with V in liters).

Example: 25.00 mL of HCl of unknown concentration needs 21.40 mL of 0.1000 M NaOH to reach the equivalence point.

  • Moles of NaOH = 0.1000 × 0.02140 = 2.140 × 10⁻³ mol.
  • Moles of HCl = the same, 2.140 × 10⁻³ mol.
  • c(HCl) = 2.140 × 10⁻³ / 0.02500 = 0.08560 M.

If the stoichiometry is not 1:1, include the ratio. For H2SO4 + 2 NaOH → Na2SO4 + 2 H2O the moles of acid are half the moles of base.

Python From titration volume to concentration

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Titration curves

A titration curve plots pH against the volume of titrant added. For a strong acid with a strong base:

  • At the start the pH is low and rises slowly.
  • Near equivalence the pH jumps by several units for a single drop.
  • At equivalence the pH is 7.00 at 25 °C.
  • After equivalence it levels off at a high value set by the excess base.

For a weak acid titrated with a strong base, the curve differs:

  • The starting pH is higher (weak acid).
  • A gently sloping region appears where a buffer exists.
  • At the half-equivalence point, [HA] = [A⁻], so pH = pKa. This is a standard way to measure Ka.
  • At equivalence the solution contains only the conjugate base, so the pH is above 7.

The program below solves the exact charge balance at each volume, so it works for both cases. With C_a the total acid concentration after dilution and Na the sodium concentration:

Na + [H⁺] = [OH⁻] + [A⁻], with [A⁻] = C_a Ka / (Ka + [H⁺]) for a weak acid.

Python Titration curves for a strong and a weak acid

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Read the table: for 0.100 M HCl the pH is 7.00 at 25.0 mL, while for acetic acid it is higher (about 8.7) because acetate is a weak base. The weak-acid column shows pH = 4.75 at 12.5 mL, the half-equivalence point, which matches pKa = 4.74 (the tiny difference comes from rounding pKa).

Choosing an indicator

An indicator is a weak acid whose conjugate forms have different colors. It changes color over a range of about two pH units around its own pKa. The range should fall inside the steep part of the curve.

Indicator Color range (approximate pH) Colors
Methyl orange 3.1 – 4.4 red to yellow
Bromothymol blue 6.0 – 7.6 yellow to blue
Phenolphthalein 8.2 – 10 colorless to pink
  • Strong acid with strong base: any of the three works, because the jump spans pH 3 to 11.
  • Weak acid with strong base: phenolphthalein (equivalence pH around 8–9).
  • Weak base with strong acid: methyl orange (equivalence pH below 7).
  • Weak acid with weak base: no sharp jump, so titration is impractical.

The end point (where the indicator changes color) should coincide closely with the equivalence point. A pH meter can record the whole curve instead.

Practical points

  • Rinse the burette with the titrant and the pipette with the analyte.
  • Do a rough titration first, then repeat until results agree within about 0.10 mL (concordant titers).
  • Read the burette at the bottom of the meniscus at eye level.
  • Standardize NaOH against a primary standard, because solid NaOH absorbs water and carbon dioxide. A primary standard is a pure, stable, weighable substance such as potassium hydrogen phthalate.

This lesson describes standard lab technique. The numbers above come from calculations, not from experiments; real results depend on your equipment and care.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. 20.00 mL of NaOH needs 15.00 mL of 0.1000 M HCl to neutralize. What is [NaOH]?

    n(HCl) = 0.1000 × 0.01500 = 1.500e-3 mol, equal to n(NaOH). Concentration = 1.500e-3 / 0.02000 = 0.0750 M.
  2. 2. In a weak acid-strong base titration, what is true at the half-equivalence point?

    Half the acid has become conjugate base, so [HA] = [A-] and the Henderson-Hasselbalch relation gives pH = pKa.
  3. 3. What is the pH at the equivalence point when a weak acid is titrated with a strong base (25 °C)?

    The solution holds only the conjugate base of the weak acid, which makes it basic.
  4. 4. Which indicator suits a weak acid titrated with a strong base?

    Phenolphthalein changes color around pH 8 to 10, which contains the equivalence pH of such a titration.

Summary

  • At equivalence, moles of titrant match moles of analyte according to the balanced equation.
  • Titration curves show a steep jump at equivalence; strong-strong equivalence is at pH 7.
  • For weak acids, pH = pKa at half equivalence and the equivalence pH is above 7.
  • Pick an indicator whose color range lies on the steep part of the curve.
  • Repeat titrations until the results are concordant.

Next: Oxidation Numbers