Skip to content
Tutorials Center
My learning

Topics

Lesson 36 of 39 · Solubility and Buffers

Buffers and the Henderson-Hasselbalch Equation

Learn how buffers resist pH change, calculate buffer pH with the Henderson-Hasselbalch equation, and design a buffer for a target pH.

Add a drop of strong acid to a glass of pure water and the pH plunges. Add the same drop to a buffer and the pH barely moves. Buffers are everywhere: in blood, in the ocean, in cells, in shampoo and in every lab that needs stable conditions.

What is a buffer?

A buffer is a solution that resists changes in pH when small amounts of acid or base are added. It contains a weak acid and its conjugate base (or a weak base and its conjugate acid) in appreciable amounts, such as acetic acid with sodium acetate.

  • Added H⁺ is consumed by the conjugate base: A⁻ + H⁺ → HA.
  • Added OH⁻ is consumed by the weak acid: HA + OH⁻ → A⁻ + H2O.

The pH changes only slightly, because the ratio [A⁻]/[HA] shifts a little but not much.

A strong acid alone is not a buffer, since it has no base to react with added acid.

The Henderson–Hasselbalch equation

Start with Ka = [H₃O⁺][A⁻] / [HA], rearrange for [H₃O⁺], and take the negative logarithm:

pH = pKa + log10( [A⁻] / [HA] )

This is the Henderson–Hasselbalch equation. Key consequences:

  • If [A⁻] = [HA], pH = pKa.
  • A tenfold ratio changes the pH by one unit.
  • Diluting a buffer (adding water) does not change the ratio, so it barely changes the pH.

Because the equation uses a ratio, you can use moles instead of concentrations when both components are in the same volume.

Worked example: an acetate buffer

Make 1.00 L of a buffer containing 0.10 mol of acetic acid and 0.10 mol of sodium acetate. Take pKa = 4.74 for acetic acid (Ka = 1.8 × 10⁻⁵).

  • Equal amounts: pH = 4.74 + log(1) = 4.74.

Now add 0.010 mol of HCl to 1.00 L of a buffer containing 0.10 mol each of HA and A⁻ (volume change ignored):

  • The acid reacts with acetate: A⁻ falls to 0.090 mol and HA rises to 0.110 mol.
  • pH = 4.74 + log(0.090 / 0.110) = 4.74 − 0.087 = 4.65.

The pH changed by only 0.09. The same 0.010 mol of HCl in 1.00 L of pure water gives [H⁺] = 0.010 M, so pH = 2.00, a drop of 5 units.

Python A buffer pH calculator

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The buffer holds until acetate is nearly used up: at 0.090 mol added HCl the ratio is 0.010 / 0.190 and the pH falls noticeably.

Buffer capacity and range

Buffer capacity is the amount of acid or base a buffer can absorb before the pH changes a lot. It is greatest when:

  • the concentrations of HA and A⁻ are high (more reservoir), and
  • the ratio [A⁻]/[HA] is close to 1.

A good rule is that a buffer works within about pKa ± 1, where the ratio is between 1/10 and 10. To make a buffer for a target pH, pick a weak acid whose pKa is close to that pH.

Weak acid / conjugate base pKa (approximate) Useful range
CH₃COOH / CH₃COO⁻ 4.74 3.7 – 5.7
H₂PO₄⁻ / HPO₄²⁻ 7.2 6.2 – 8.2
NH₄⁺ / NH₃ 9.25 8.3 – 10.3

Designing a buffer

Make 1.00 L of buffer at pH 5.00 from acetic acid and sodium acetate with total concentration 0.200 M.

5.00 = 4.74 + log(r), so r = [A⁻]/[HA] = 10^0.26 = 1.82.

[A⁻] + [HA] = 0.200, so [HA] = 0.200 / 2.82 ≈ 0.071 M and [A⁻] ≈ 0.129 M.

Python Design a buffer for a target pH

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

In the lab you would measure out these amounts and then check with a pH meter, adjusting if needed, because real activities differ from ideal.

Buffers in nature

Human arterial blood has a pH of about 7.35–7.45, held mainly by the carbonic acid/hydrogen carbonate system (and also by proteins and phosphate). The respiratory system adjusts how much CO₂ is exhaled, and the kidneys adjust hydrogen carbonate, so the buffer is continually refreshed. A blood pH outside the narrow range is a medical emergency.

The Henderson–Hasselbalch equation is an approximation. It works best when both components are present at concentrations well above [H₃O⁺] and when the acid is not too strong or too concentrated or too dilute.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. What is the pH of a buffer made of equal concentrations of acetic acid and acetate (pKa = 4.74)?

    When [A-] = [HA], the log term is zero and pH = pKa.
  2. 2. A buffer has [A-]/[HA] = 10. What is the pH relative to pKa?

    log10(10) = 1, so pH = pKa + 1.
  3. 3. Which pair makes the best buffer at pH 9.2?

    The pKa should be within about one unit of the target pH, and 9.25 is closest.
  4. 4. What happens to the pH of a buffer when it is diluted with an equal volume of water?

    The concentration ratio of base to acid is unchanged by dilution, so the pH stays almost the same (but the capacity falls).

Summary

  • A buffer contains a weak acid and its conjugate base and resists pH change.
  • pH = pKa + log([A⁻]/[HA]); equal amounts give pH = pKa.
  • Buffers work best within pKa ± 1 and have greater capacity at higher concentration.
  • To design one, choose an acid with pKa near the target and solve for the ratio.
  • Blood is buffered mainly by the carbonic acid/hydrogen carbonate system.

Next: Practice Set: Equilibrium and Acids and Bases