Skip to content
Tutorials Center
My learning

Topics

Lesson 32 of 38 · AC Circuits and Electromagnetic Waves

Reactance and Impedance

Learn how inductors and capacitors resist alternating current: inductive and capacitive reactance, impedance, phase angle and the series RLC circuit, with worked examples.

A resistor resists current the same way at every frequency. Inductors and capacitors do not. A capacitor lets high-frequency signals through and blocks steady DC; an inductor does the opposite. This frequency-dependent opposition is the basis of every radio tuner, audio crossover (which sends bass to the woofer and treble to the tweeter) and power filter.

In this lesson you will define reactance for inductors and capacitors, combine them with resistance into impedance, and solve a series RLC circuit.

Inductive reactance

Connect an ideal inductor L to an AC source v = V₀ sin(ω t). The inductor's EMF opposes changes in current, so v = L dI/dt. Integrating gives a current with the same frequency, a peak value I₀ = V₀ / (ω L), and lagging the voltage by 90°. The ratio of peak (or RMS) voltage to current is the inductive reactance:

Text
X_L = ω L = 2π f L        (unit: ohm)

It increases with frequency. At f = 0 (DC), X_L = 0: the inductor is just a wire. At very high frequencies the inductor almost blocks the current.

Capacitive reactance

For an ideal capacitor C, the charge follows the voltage: q = C v, so the current i = dq/dt = C dv/dt. The result is a current with peak I₀ = ω C V₀, leading the voltage by 90°. The capacitive reactance is

Text
X_C = 1 / (ω C) = 1 / (2π f C)        (unit: ohm)

It decreases with frequency. At DC (f = 0) it is infinite: the capacitor blocks steady current. At high frequencies it passes current easily.

Python Reactance versus frequency

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The series RLC circuit and impedance

Put a resistor R, an inductor L and a capacitor C in series with an AC source. The same current flows through all three, but the voltages across them are not in phase with one another:

  • V_R is in phase with the current.
  • V_L leads the current by 90°.
  • V_C lags the current by 90°.

Because V_L and V_C point in opposite directions, they partly cancel. We add them as phasors, arrows whose length is the amplitude and whose angle is the phase. The result, with V_R = I R, V_L = I X_L and V_C = I X_C, is:

Text
V₀² = V_R² + (V_L - V_C)²

Divide by I² to get the impedance Z, the effective opposition of the whole circuit:

Text
Z = √( R² + (X_L - X_C)² )
V₀ = I₀ Z,   V_rms = I_rms Z

The phase angle φ by which the voltage leads the current is

Text
tan φ = (X_L - X_C) / R

If X_L > X_C the circuit is inductive (φ > 0, current lags). If X_C > X_L it is capacitive (φ < 0, current leads). If X_L = X_C the reactances cancel and Z = R, the resonance condition of the next lesson.

flowchart TB
  A["Resistance R"] --> Z["Impedance Z = sqrt(R² + (X_L - X_C)²)"]
  B["Inductive reactance X_L = ωL"] --> Z
  C["Capacitive reactance X_C = 1/(ωC)"] --> Z
  Z --> P["Phase angle: tan φ = (X_L - X_C)/R"]

Resistance and the net reactance combine at right angles, like the sides of a right triangle.

Worked example

A series circuit has R = 100 Ω, L = 0.20 H, C = 20 μF, and a 230 V RMS, 50 Hz supply.

  1. ω = 2π × 50 ≈ 314.16 rad/s.
  2. X_L = ω L = 314.16 × 0.20 ≈ 62.8 Ω.
  3. X_C = 1 / (ω C) = 1 / (314.16 × 20×10⁻⁶) ≈ 159.2 Ω.
  4. Net reactance: X_L - X_C ≈ -96.3 Ω (capacitive).
  5. Z = √(100² + 96.3²) ≈ 138.8 Ω.
  6. I_rms = 230 / 138.8 ≈ 1.66 A.
  7. tan φ = -96.3 / 100, so φ ≈ -43.9°: the current leads the voltage by about 44°.
  8. Power factor cos φ = R / Z ≈ 0.72; average power P = I_rms² R ≈ 275 W.
Python A series RLC impedance calculator

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Notice that the resistor is the only component that uses power. The inductor and capacitor store energy and give it back each cycle.

Voltages can exceed the supply

Add the voltage amplitudes arithmetically and the total exceeds the supply. In our example at 1.66 A, V_C ≈ 1.66 × 159.2 ≈ 264 V and V_L ≈ 104 V, each of which can be comparable to or larger than the supply, yet the supply is only 230 V. This is possible because V_L and V_C are 180° apart, so they cancel in the sum. Components must be rated for these individual voltages.

Simple filters

An RC circuit with the output taken across the capacitor is a low-pass filter: at low frequencies X_C is large and most of the voltage appears across C; at high frequencies X_C is small and the output drops. Swap the positions (output across the resistor) and you get a high-pass filter. The frequency where R = X_C is called the cutoff, f_c = 1 / (2π R C).

Python Gain of an RC low-pass filter

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

At the cutoff frequency the gain is 1/√2 ≈ 0.707, which corresponds to half the power.

Common mistakes

  • Adding R, X_L and X_C arithmetically. They must be combined with √(R² + (X_L - X_C)²).
  • Using f where ω is required in X_L or X_C.
  • Forgetting the units: capacitance must be in farads (convert μF).
  • Assuming X_C increases with frequency. It decreases.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. What is the inductive reactance of a 0.10 H inductor at 100 Hz?

    X_L = 2π f L = 2π × 100 × 0.10 ≈ 62.8 Ω.
  2. 2. A 10 μF capacitor is used at 50 Hz. What is its reactance?

    X_C = 1 / (2π × 50 × 10×10⁻⁶) ≈ 318 Ω.
  3. 3. A series circuit has R = 30 Ω, X_L = 80 Ω and X_C = 40 Ω. What is the impedance?

    Z = √(30² + (80 - 40)²) = √(900 + 1600) = 50 Ω.
  4. 4. If the frequency is raised, what happens to X_L and X_C?

    X_L = 2π f L grows with f; X_C = 1 / (2π f C) shrinks.

Summary

  • X_L = ω L (rises with frequency, current lags by 90°); X_C = 1 / (ω C) (falls with frequency, current leads by 90°).
  • Series RLC impedance: Z = √(R² + (X_L - X_C)²), V = I Z, tan φ = (X_L - X_C) / R.
  • Only the resistor dissipates power; P = I_rms² R = V_rms I_rms cos φ.
  • Reactances of opposite type cancel, so the voltage across L or C can exceed the supply.
  • RC and RL networks work as low-pass and high-pass filters.

Next: Resonance and Power Factor