Skip to content
Tutorials Center
My learning

Topics

Lesson 19 of 38 · DC Circuits

EMF and Internal Resistance

Learn the difference between EMF and terminal voltage, how internal resistance drops the voltage of a real battery, and when a source delivers maximum power.

A battery is labeled 12 V, yet when you connect a heavy load the voltage across its terminals drops a little. Why? Because a real source is not a perfect voltage maker. Inside it, charges must move through chemicals, plates and wires, and that path resists current just like any resistor.

In this lesson you will separate two ideas that beginners often mix up: the EMF of a source and the terminal voltage you can actually measure. You will learn how to model a real battery, calculate the "lost" voltage, and find the load that draws the most power from it. You should already know Ohm's law (V = I R) from the earlier chapters on current and resistance.

EMF: the energy given to each coulomb

The electromotive force (EMF, symbol ε) of a source is the energy it gives to each coulomb of charge that passes through it. The name is old and misleading: EMF is not a force. It is measured in volts, where 1 V = 1 J/C.

A 12 V battery gives 12 J to every coulomb that goes through it, when the charge is pushed through the source's chemistry. The EMF is a property of the source itself. It is the voltage you would measure across the terminals if no current flowed at all (an open circuit), for example with a good voltmeter whose resistance is very large.

Internal resistance and terminal voltage

Real sources waste a little of that energy as heat inside themselves. We model this by drawing the source as a perfect EMF ε in series with a small resistor r, called the internal resistance.

flowchart LR
  A["EMF ε"] --> B["internal resistance r"] --> C["terminals"] --> D["load R"] --> A

A real source is an ideal EMF in series with its internal resistance. The load R is connected across the terminals.

When a current I flows, the internal resistor drops a voltage I r. What is left for the outside circuit is the terminal voltage:

Text
V = ε - I r

The same current flows through the load, so V = I R. Combine the two equations and you get the current in the whole loop:

Text
I = ε / (R + r)

Notice that the circuit behaves as if the source and the load were two resistors in series, R and r, sharing the EMF.

Worked example

A battery has ε = 12.0 V and r = 0.50 Ω. It is connected to a load of R = 5.5 Ω.

  1. Total resistance: R + r = 6.0 Ω.
  2. Current: I = 12.0 / 6.0 = 2.0 A.
  3. Lost volts: I r = 2.0 × 0.50 = 1.0 V.
  4. Terminal voltage: V = 12.0 - 1.0 = 11.0 V.
  5. Check using the load: I R = 2.0 × 5.5 = 11.0 V. It matches.
Python Terminal voltage for different loads

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Look at the pattern. A large load resistance draws a small current, so almost nothing is lost inside, and V is very close to ε. A tiny load resistance draws a huge current, and the terminal voltage collapses. The last row (R = 0) is a short circuit: the whole EMF falls across r, the current is ε / r, and all the heat is produced inside the battery. That is why shorting a battery makes it hot, and can be dangerous.

Never short-circuit a battery on purpose. The current is limited only by the tiny internal resistance, so the battery, or the wires, can overheat quickly.

Why terminal voltage falls as current rises

The relation V = ε - I r is the equation of a straight line. If you plot V against I, the intercept on the voltage axis is the EMF, and the slope is -r. This gives a standard laboratory method: vary a rheostat (a variable resistor), record pairs of readings from a voltmeter and an ammeter, plot the graph, and read off ε and r.

Python Fit a straight line to V and I data

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

This is a simulation of a lab experiment, not real data. The noise is invented only to show that a best-fit line recovers the hidden values.

Maximum power transfer

How much power does the load receive? It is P = I² R, and I = ε / (R + r), so:

Text
P = ε² R / (R + r)²

If R is tiny, the current is large but R is small, so P is small. If R is huge, the current is tiny, so P is small again. Somewhere in between is a peak. Setting the slope of P to zero shows that the peak occurs at R = r. At that point the power delivered is P_max = ε² / (4 r).

For our battery, P_max = 144 / (4 × 0.50) = 72 W at R = 0.50 Ω. Half of the total power is wasted inside the source at that moment (efficiency 50%). Engineers who care about efficiency, such as in power grids, deliberately use a load much larger than r. People who care about transferring a signal (for example from a microphone to an amplifier) may match the resistances instead.

Python Find the load that receives the most power

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Common mistakes

  • Treating the label on a battery as the voltage under all conditions. The label is the EMF (or close to it); the terminal voltage depends on the current drawn.
  • Using V = ε + I r when the source is being charged. When current is forced backward through a source (as in a recharging battery), the terminal voltage is higher than the EMF: V = ε + I r.
  • Forgetting that the same current flows through r and R, because they are in series.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. A source has EMF 9.0 V and internal resistance 1.0 Ω. It drives a 8.0 Ω load. What is the terminal voltage?

    I = 9.0 / (8.0 + 1.0) = 1.0 A. The lost volts are I r = 1.0 V, so V = 9.0 - 1.0 = 8.0 V.
  2. 2. When does the terminal voltage of a discharging battery equal its EMF?

    With I = 0 there is no voltage lost across r, so V = ε. This is the open-circuit condition.
  3. 3. A source has ε = 6.0 V and r = 2.0 Ω. What is the maximum power it can deliver to a load?

    Maximum power occurs when R = r, and P_max = ε² / (4 r) = 36 / 8 = 4.5 W.
  4. 4. On a graph of terminal voltage against current, what does the gradient represent?

    V = ε - I r is a straight line with intercept ε and gradient -r.

Summary

  • EMF ε is the energy per coulomb the source supplies; it equals the terminal voltage when no current flows.
  • A real source is an ideal EMF in series with an internal resistance r.
  • Terminal voltage: V = ε - I r; loop current: I = ε / (R + r).
  • A large current drags the terminal voltage down; a short circuit puts all the EMF across r.
  • The load receives maximum power when R = r, which is ε² / (4 r).

Next: Resistors in Series and Parallel