Skip to content
Tutorials Center
My learning

Topics

Lesson 27 of 38 · Electromagnetic Induction

Magnetic Flux and Faraday's Law

Understand magnetic flux and Faraday's law of electromagnetic induction: how a changing flux through a coil produces an EMF, with worked examples and code.

So far, currents have made magnetic fields. In 1831 Michael Faraday (in England) and Joseph Henry (in the United States) discovered the reverse: a changing magnetic field can make a current flow in a circuit with no battery at all. This effect, called electromagnetic induction, powers the world. Almost all of the electricity you use comes from generators that rely on it, and transformers, induction cooktops, wireless chargers and guitar pickups use it too.

This lesson defines magnetic flux, states Faraday's law, and works through the numbers.

Magnetic flux

Imagine field lines passing through a loop. The magnetic flux Φ measures how much field "goes through" the loop's surface. For a flat loop of area A in a uniform field B:

Text
Φ = B A cos θ

where θ is the angle between the field and the normal to the loop (the line perpendicular to its surface). The unit is the weber (Wb): 1 Wb = 1 T·m².

  • Loop face-on to the field (θ = 0°): maximum flux, Φ = B A.
  • Loop edge-on (θ = 90°): no field passes through, Φ = 0.

Flux can change in three ways: the field strength B changes, the area A changes, or the angle θ changes.

Faraday's law

Faraday's law says that the induced EMF in a coil equals the rate of change of the magnetic flux through it:

Text
ε = -N dΦ/dt

N is the number of turns, since each turn contributes the same EMF and they add in series. If the flux changes at a steady rate over a time Δt, then the average EMF is ε = -N ΔΦ / Δt.

The EMF depends on how fast the flux changes, not on how large the flux is. A strong steady field induces nothing. The minus sign is Lenz's law, covered in the next lesson; it fixes the direction of the induced current. For now we mostly care about magnitudes.

If the coil is part of a closed circuit with resistance R, the induced current is I = ε / R.

Worked example

A coil of N = 200 turns has area A = 0.010 m². A field perpendicular to its face increases from 0 to 0.50 T in 0.20 s.

  1. Flux change: ΔΦ = ΔB × A = 0.50 × 0.010 = 5.0×10⁻³ Wb.
  2. Magnitude of EMF: ε = N ΔΦ / Δt = 200 × 5.0×10⁻³ / 0.20 = 5.0 V.
  3. If the circuit resistance is 10 Ω, the current is I = 5.0 / 10 = 0.50 A.
Python EMF from a changing field

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Rate of change is what matters

Consider a coil in a field B(t) = B₀ sin(ω t). The flux through each turn is Φ(t) = B₀ A sin(ω t), and the EMF is the slope of the flux curve, times -N. The slope of a sine is a cosine, so the EMF is largest when the flux is zero (and changing fastest), and the EMF is zero when the flux is at its peak (momentarily not changing).

Python Flux and EMF: slope of a sine wave

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The flux and the EMF are a quarter of a cycle apart, a first hint of the phase differences you will meet in AC circuits.

Ways to induce an EMF

flowchart TB
  A["Change in flux through a coil"] --> B["Change B: move a magnet, vary a current"]
  A --> C["Change A: stretch or shrink the loop"]
  A --> D["Change θ: rotate the loop"]
  B --> E["EMF = -N dΦ/dt"]
  C --> E
  D --> E

Any of the three variables in Φ = B A cos θ can drive induction.

Typical demonstrations: push a bar magnet into a coil connected to a sensitive meter and the needle jumps; pull it out and the needle jumps the opposite way. Hold the magnet still inside the coil and the reading falls back to zero. Moving the magnet faster or using more turns gives a larger reading. These results match ε = -N dΦ/dt.

Induced electric fields

A changing magnetic field does more than make a current in a wire. It creates an electric field in the space around it, even where there is no wire. This induced field is not like the one from static charges: its field lines form closed loops, and it is non-conservative. The EMF around a loop is ε = ∮ E · dl, so Faraday's law can also be written ∮ E · dl = -dΦ/dt. This is one of Maxwell's four equations, which you will use in the electromagnetic waves lesson.

Common mistakes

  • Thinking a large field gives a large EMF. Only a changing flux does.
  • Forgetting the number of turns N.
  • Using the angle between B and the loop's plane rather than the normal in cos θ.
  • Forgetting to convert units: cm² to m², mT to T.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. A 0.050 m² loop is perpendicular to a 0.40 T field. What is the flux?

    Φ = B A cos 0° = 0.40 × 0.050 = 2.0×10⁻² Wb.
  2. 2. A 50-turn coil sees its flux drop uniformly from 4.0×10⁻³ Wb to zero in 0.10 s. What is the average EMF magnitude?

    ε = N ΔΦ / Δt = 50 × 4.0×10⁻³ / 0.10 = 2.0 V.
  3. 3. A bar magnet is held at rest inside a coil. What is the induced EMF?

    EMF depends on the rate of change of flux. A steady flux induces nothing.
  4. 4. Which change does NOT alter the flux through a loop?

    In a uniform field with constant angle and area, the flux is unchanged, so no EMF is induced.

Summary

  • Magnetic flux: Φ = B A cos θ, in webers (1 Wb = 1 T·m²).
  • Faraday's law: ε = -N dΦ/dt; EMF depends on how fast the flux changes.
  • Flux changes when B, A or θ change.
  • A changing magnetic field creates a non-conservative electric field.
  • The induced current in a closed circuit is I = ε / R.

Next: Lenz's Law and Motional EMF