Skip to content
Tutorials Center
My learning

Topics

Lesson 18 of 38 · Current and Resistance

Electric Power and Energy

Learn electric power P = IV = I²R = V²/R, how resistors turn energy into heat, and how to compute the energy and cost of running appliances in kWh.

A battery gives energy to charges, and the charges deliver it to the devices in the circuit: light, heat, motion, sound. How fast energy is delivered is power. This is also what your electricity bill is based on. In this lesson you connect voltage, current and resistance to power, and learn to calculate energy costs.

Power in a circuit element

A charge q moving through a potential difference V changes its potential energy by qV. Current is the rate at which charge flows, so the rate of energy transfer is

Text
P = ΔU/Δt = (ΔQ/Δt) V = I V        unit: watt (W), 1 W = 1 J/s = 1 V·A

This works for any device. For a resistor you can use V = IR to get two more forms:

Text
P = I² R = V² / R

All three give the same answer for a resistor. Which to use depends on what you know: use I²R when the same current flows through different resistors (series), and V²/R when the same voltage acts across them (parallel).

The energy delivered in time t is E = P t.

Python Three ways to get power

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Where does the energy go?

In a resistor the electrical energy turns into thermal energy (heating). This is called Joule heating. It is useful in a toaster or kettle and wasteful in a power cable.

Why does it happen? The carriers gain kinetic energy from the field between collisions and give it to the lattice atoms at each collision. The atoms vibrate more: the material warms.

In other devices, the energy goes elsewhere. In a motor, much becomes mechanical work. In a battery being charged, it becomes chemical energy. In an LED, most becomes light. The formula P = IV still gives the total rate of energy delivered.

Power in transmission lines

Why is electricity sent over long distances at very high voltage? Take a town that needs power P. The current in the line is I = P/V. The line has resistance R, and wastes P_loss = I² R = P² R / V². If you raise the voltage by a factor of 10, the loss falls by a factor of 100.

Python Power loss in a transmission line

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

At 10 kV the line carries 500 A, so it wastes 500 kW, which is 10% of the delivered power. At 400 kV the loss is negligible. That is why power grids use transformers to step the voltage up for transmission and down for homes (see the induction chapter).

Energy bills and the kilowatt-hour

Electricity companies sell energy in kilowatt-hours (kWh):

Text
1 kWh = 1000 W × 3600 s = 3.6 × 10⁶ J

Cost = energy in kWh × price per kWh. Example: a 2.0 kW kettle that runs for 3.0 minutes per day uses 2.0 × 3/60 = 0.10 kWh per day.

Python Energy and cost of appliances

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The appliance figures are illustrative assumptions, not measurements; use the rating plate on your own devices for real values.

Efficiency

Not all power does useful work. Efficiency is useful output power / input power. A good LED turns a larger fraction of its input into light than a filament bulb, which wastes most energy as heat. A kettle is close to 100% efficient at heating the water in it (apart from heat lost to the surroundings).

Keep two things apart: power (W, a rate) and energy (J or kWh, a total). Saying "a 60 W bulb uses 60 W per hour" is wrong; it uses 60 W of power, which is 0.06 kWh of energy per hour.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. A 240 V heater draws 5.0 A. Its power is

    P = IV = 5.0 × 240 = 1200 W.
  2. 2. A 100 Ω resistor carries 0.30 A. The power dissipated is

    P = I²R = 0.09 × 100 = 9.0 W.
  3. 3. How much energy does a 1500 W heater use in 2.0 hours?

    E = 1.5 kW × 2.0 h = 3.0 kWh.
  4. 4. Why is power transmitted at high voltage?

    For fixed power, I = P/V, so a higher V means a smaller I and a much smaller I²R loss.

Summary

  • P = IV = I²R = V²/R, in watts; E = Pt.
  • Resistors convert electrical energy into heat (Joule heating).
  • 1 kWh = 3.6 × 10⁶ J; cost = kWh × tariff.
  • High-voltage transmission cuts I²R losses.

Next: EMF and Internal Resistance