Skip to content
Tutorials Center
My learning

Topics

Lesson 36 of 38 · Projects and Practice

Practice Set: DC Circuits

Practice DC circuit problems on internal resistance, series-parallel networks, Kirchhoff's laws, RC charging and power, each with a worked solution and Python check.

Reading about circuits is not the same as solving them. This practice set gives you five problems that mix the ideas from the DC circuits chapter: internal resistance, resistor networks, Kirchhoff's laws, and RC circuits. Try each one on paper first, using the hints. Then open the worked solution and run the Python check to confirm your numbers.

A good problem-solving routine saves you from most errors:

  1. Draw the circuit and label every known and unknown quantity, with units.
  2. Choose the principle that applies (series/parallel reduction, loop rule, junction rule, time constant).
  3. Write the equations symbolically before substituting numbers.
  4. Solve, then check: do the answers have sensible size and sign? Does power supplied equal power dissipated?

See EMF and internal resistance, series and parallel resistors, Kirchhoff's laws and RC circuits if you need a refresher.

Problem 1: a tired battery

A battery has EMF 9.0 V and internal resistance 0.60 Ω. It is connected to a 4.4 Ω resistor.

(a) Find the current. (b) Find the terminal voltage. (c) Find the power wasted inside the battery.

Solution. The load and the internal resistance are in series: R_total = 4.4 + 0.60 = 5.0 Ω, so I = 9.0 / 5.0 = 1.8 A. The lost volts are I r = 1.8 × 0.60 = 1.08 V, so the terminal voltage is 9.0 - 1.08 = 7.92 V. Check using the load: 1.8 × 4.4 = 7.92 V. The power wasted inside is I² r = 1.8² × 0.60 ≈ 1.94 W.

Python Check problem 1

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Problem 2: a ladder of resistors

A 12 V source (no internal resistance) is connected to a 3.0 Ω resistor in series with a parallel pair of 6.0 Ω and 3.0 Ω. Find the current in each resistor.

Hint. Reduce the parallel pair first.

Solution. The parallel pair is (6 × 3) / (6 + 3) = 2.0 Ω. Total: 3.0 + 2.0 = 5.0 Ω, so the source current is 12 / 5.0 = 2.4 A. This flows through the 3.0 Ω resistor, which drops 7.2 V. The pair has 12 - 7.2 = 4.8 V across it, so the 6.0 Ω branch carries 0.80 A and the 3.0 Ω branch 1.6 A (sum 2.4 A, as required).

Python Check problem 2

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Problem 3: two batteries sharing a load

Two batteries are connected in parallel through their own resistors to a common load. Battery 1: ε₁ = 9.0 V, R₁ = 1.0 Ω. Battery 2: ε₂ = 3.0 V, R₂ = 2.0 Ω. The shared load is R₃ = 4.0 Ω. Find the current in each branch, and say whether battery 2 is discharging or charging.

Hint. Use I₃ = I₁ + I₂ and one loop equation through each battery and the load.

Solution. Loop 1: 9 - 1.0 I₁ - 4.0 (I₁ + I₂) = 0 gives 5 I₁ + 4 I₂ = 9. Loop 2: 3 - 2.0 I₂ - 4.0 (I₁ + I₂) = 0 gives 4 I₁ + 6 I₂ = 3. Solving: I₁ = 3.0 A, I₂ = -1.5 A, I₃ = 1.5 A. The negative value means battery 2 is being charged by battery 1.

Python Check problem 3

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Problem 4: a timer circuit

A 10 μF capacitor is charged through a 100 kΩ resistor from a 6.0 V supply. (a) What is the time constant? (b) How long until the capacitor voltage is 4.5 V? (c) What is the current at that moment?

Solution. (a) τ = R C = 100 000 × 10×10⁻⁶ = 1.0 s. (b) 4.5 = 6.0 (1 - e^(-t/τ)) gives e^(-t/τ) = 0.25, so t = τ ln 4 ≈ 1.39 s. (c) The resistor has 6.0 - 4.5 = 1.5 V across it, so I = 1.5 / 100 000 = 15 μA.

Python Check problem 4

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Problem 5: choose the load

A source has ε = 12 V and r = 3.0 Ω. Which of the loads 1.0 Ω, 3.0 Ω, 9.0 Ω receives the most power? How much?

Solution. The load power is P = ε² R / (R + r)². For 1.0 Ω: 144 / 16 = 9.0 W. For 3.0 Ω: 432 / 36 = 12 W. For 9.0 Ω: 1296 / 144 = 9.0 W. The 3.0 Ω load, which equals r, receives the most (12 W): the maximum-power condition.

Python Check problem 5

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Test yourself

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. A 12 V battery with internal resistance 0.40 Ω drives a current of 5.0 A. What is the terminal voltage?

    V = ε - I r = 12 - 5.0 × 0.40 = 10 V.
  2. 2. What is the equivalent resistance of 8.0 Ω and 8.0 Ω in parallel, in series with 2.0 Ω?

    The parallel pair is 4.0 Ω; adding 2.0 Ω in series gives 6.0 Ω.
  3. 3. In a charging RC circuit, how many time constants until the capacitor reaches about 95% of its final voltage?

    1 - e⁻³ ≈ 0.950, so about three time constants.
  4. 4. When using Kirchhoff's laws, a solved current is negative. What should you do?

    A negative value just means the real current flows opposite to the assumed arrow.

Summary

  • Always check results with an independent route: power in equals power out, or a loop you did not use.
  • Internal resistance: V = ε - I r; maximum load power at R = r.
  • Reduce series-parallel networks from the far end toward the source.
  • Kirchhoff: junction rule for charge, loop rule for energy; negative currents mean reversed arrows.
  • RC: τ = R C, t = -τ ln(1 - V/ε).

Next: Practice Set: Magnetism and Induction