Skip to content
Tutorials Center
My learning

Topics

Lesson 22 of 38 · DC Circuits

RC Circuits: Charging and Discharging

Learn how a resistor and capacitor shape voltage over time: the time constant, exponential charging and discharging, and how to calculate values with examples.

Everything so far in this chapter reached a steady state instantly. Add a capacitor, and the story changes: the current and voltages now evolve over time. A camera flash charges up before it fires. A touch sensor measures how long a capacitor takes to fill. A turn-signal flasher, a debounce circuit for a button, and the smoothing of a rectified power supply all rely on the same simple idea.

An RC circuit contains a resistor R and a capacitor C. In this lesson you will learn the time constant, the formulas for charging and discharging, and how to use them in calculations. You should know that a capacitor stores charge Q = C V (from the previous chapter).

The time constant

The product τ = R C (the Greek letter tau) has the unit of time: ohm times farad equals second. It is called the time constant. A big resistor limits the current, so the capacitor fills slowly. A big capacitor needs more charge to reach the same voltage, so it also takes longer. Hence larger R or larger C means a larger τ and a slower circuit.

For example, R = 10 kΩ and C = 100 μF give τ = 10 000 × 100×10⁻⁶ = 1.0 s.

Charging a capacitor

Connect an uncharged capacitor in series with a resistor to a battery of EMF ε (assume negligible internal resistance), and close the switch at t = 0.

At the first instant the capacitor has no voltage, so the whole EMF is across the resistor and the current is largest: I₀ = ε / R. As charge builds up, the capacitor voltage V_C = q / C rises, leaving less voltage across the resistor, so the current shrinks. The loop rule gives ε = I R + q / C, whose solution is:

Text
q(t)   = C ε (1 - e^(-t/τ))
V_C(t) = ε (1 - e^(-t/τ))
I(t)   = (ε / R) e^(-t/τ)

The charge approaches its final value Q = C ε but never quite arrives. After one time constant the capacitor has reached 1 - e⁻¹ ≈ 63.2% of its final voltage. The current has dropped to e⁻¹ ≈ 36.8% of its starting value.

Time Fraction of final charge
1 τ 63.2%
2 τ 86.5%
3 τ 95.0%
5 τ 99.3%

In practice we say a capacitor is "fully charged" after about 5 τ.

Python Charging curve values

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Discharging a capacitor

Now charge a capacitor to V₀, remove the battery and let it discharge through the resistor. The capacitor acts as the source, so the voltage falls and, with it, the current:

Text
q(t)   = Q₀ e^(-t/τ)
V_C(t) = V₀ e^(-t/τ)
I(t)   = (V₀ / R) e^(-t/τ)   (flows in the opposite sense to charging)

After 1 τ the voltage is 36.8% of the original. After 5 τ it is under 1%. A related useful number is the half-life, the time to fall to half: t½ = τ ln 2 ≈ 0.693 τ.

flowchart LR
  A["Charging: V rises toward ε"] --> B["Switch flipped"]
  B --> C["Discharging: V falls toward 0"]

The same RC pair charges and discharges with the same time constant.

Python Plot charging and discharging

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Worked example: how long to reach a given voltage?

A 4.7 μF capacitor charges through 220 kΩ from a 5.0 V supply. How long until the capacitor reaches 4.0 V?

  1. τ = R C = 220 000 × 4.7×10⁻⁶ ≈ 1.034 s.
  2. Use V = ε (1 - e^(-t/τ)): 4.0 = 5.0 (1 - e^(-t/τ)), so e^(-t/τ) = 0.20.
  3. Take natural logs: t/τ = ln 5 ≈ 1.609.
  4. t = 1.609 × 1.034 ≈ 1.66 s.

The general result is t = -τ ln(1 - V/ε). For discharging from V₀ down to V, use t = -τ ln(V / V₀) = τ ln(V₀ / V).

Python Time to reach a target voltage

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Energy in the RC circuit

While charging from a battery, the battery supplies energy ε Q = C ε². The capacitor ends up storing only ½ C ε². The other half is turned into heat in the resistor, no matter how big or small R is. This surprising fact is a result of the exponential current: a small R gives a big, quick surge, a large R a slow trickle, but the total heating is identical.

Common mistakes

  • Thinking the capacitor charges linearly. The rate of charging is proportional to the voltage still missing, so it slows down.
  • Mixing units. R in kΩ and C in μF gives τ in milliseconds; convert carefully, or work in base SI units.
  • Forgetting that the current in a charging capacitor decays, while the capacitor voltage grows.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. What is the time constant of a 2.0 kΩ resistor and a 50 μF capacitor?

    τ = R C = 2000 × 50×10⁻⁶ = 0.10 s.
  2. 2. A capacitor is charging through a resistor. After one time constant, the capacitor voltage is about what fraction of the supply EMF?

    V = ε (1 - e⁻¹) ≈ 0.632 ε.
  3. 3. At the instant a discharged capacitor is connected to a battery through a resistor, what is the current?

    The capacitor has no voltage yet, so the full EMF appears across the resistor and I = ε / R.
  4. 4. Doubling both R and C in an RC circuit does what to the time constant?

    τ = R C, so doubling each makes τ four times larger.

Summary

  • The time constant τ = R C sets the speed of charging and discharging.
  • Charging: V_C = ε (1 - e^(-t/τ)); the current decays as (ε/R) e^(-t/τ).
  • Discharging: V_C = V₀ e^(-t/τ).
  • After 1 τ: 63% charged (or 37% left); after 5 τ: effectively complete.
  • Time to reach a voltage: t = -τ ln(1 - V/ε) when charging.
  • Charging from a battery wastes half the supplied energy as heat in the resistor.

Next: Magnetic Fields and Forces on Moving Charges