Skip to content
Tutorials Center
My learning

Topics

Lesson 16 of 38 ยท Editing and Modify Tools

TRIM, EXTEND, FILLET and CHAMFER in AutoCAD

Clean up geometry with TRIM and EXTEND (cutting edges, quick mode), round and bevel corners with FILLET and CHAMFER, including radius 0 corners, plus the intersection and tangent-point math.

You rarely draw lines at their final length. The usual workflow is to draw generously, then trim the excess and extend short ends, and finish corners with fillet and chamfer. These four commands make drawings tidy and are used in almost every session. This lesson covers how they work, the modes that save time, and the geometry underneath.

TRIM

TR. In current versions, TRIM starts with the prompt Select objects or <select all>:. You choose the cutting edges (the objects that do the cutting), or press Enter to select all objects as cutting edges. Then click the portion of each object you want to remove. Shift-click an object to extend instead of trim (swapping modes on the fly).

Key options at the prompt [Fence/Crossing/Project/Edge/eRase/Undo]:

  • Fence (F) and Crossing (C): drag across many pieces to trim them all at once.
  • Edge (E): Extend lets cutting edges act as if infinite; No extend trims only where they truly cross. Setting Extend allows trimming against an edge that does not quite reach.
  • eRase (R): delete objects without leaving the command.
  • Undo (U): undo the last trim.
  • Mode: Quick vs Standard. Quick mode (the default in recent versions) uses all objects as cutting edges automatically. Standard mode makes you pick edges first. If the first prompt asks "Select cutting edges", that version uses the older flow.

Example: a room outline made with crossing wall lines. TR, Enter (select all), then click each overshoot. Corners close cleanly.

EXTEND

EX is TRIM's opposite: select boundary edges, then click the objects to lengthen up to those edges. Same options (Fence, Crossing, Project, Edge, Undo), and Shift-click trims instead. Objects extend along their own path: lines straight on, arcs along their circle. A circle or closed polyline cannot be extended.

Tip: if EXTEND does nothing because the boundary is not in the line's path, set Edge > Extend so the boundary is treated as infinite.

FILLET

F. Joins two objects with a tangent arc of a given radius. Steps: type R, enter the radius, then pick the first object near the end you want to keep, then the second.

  • Radius 0 makes a sharp corner: it trims or extends both objects exactly to their intersection. This is the standard way to clean a corner or close a small gap.
  • Polyline (P) fillets all vertices of a polyline at once.
  • Trim/No trim (T): keep the original ends instead of trimming them.
  • Multiple (M): fillet many corner pairs without restarting the command.
  • Hold Shift while picking the second object to apply radius 0 temporarily.

If the radius is too large for the objects, AutoCAD tells you "radius is too large". Lines that are parallel can also be filleted: the result is a semicircle joining them (radius ignored; it is half the gap).

CHAMFER

CHA. Like fillet but with a straight bevel. Options: Distance (D) sets two distances along each line, Angle (A) sets one distance and an angle, Polyline (P), Trim (T), Method (E) to choose distance or angle and Multiple (M). As with fillet, distances of 0 give a sharp corner.

The geometry

Trim and extend rely on finding where two objects meet. For lines, that's the standard line-line intersection (extended infinitely when needed). A fillet requires the centre of a circle tangent to both lines at distance r from each, which lies on the angle bisector; tangent points are where that circle touches the lines. The first stand-in shows the intersection and trimming.

Python Stand-in: line intersection and trim to a cutting edge

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Fillet maths

For two lines meeting at corner C with an interior angle theta, a fillet of radius r has tangent points at distance d = r / tan(theta / 2) from the corner along each line. The stand-in computes the tangent points and the arc centre for two perpendicular lines, and also the chamfer ends.

Python Stand-in: FILLET tangent points and CHAMFER ends

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

For a right-angle corner the tangent distance equals the radius, so a radius 10 fillet starts 10 units from the corner on each side, and its centre is at (10, 10).

Workflow patterns

  • Draw long, trim to fit. Draw a grid of construction lines past the edges, then TRIM with select-all.
  • Close gaps with FILLET radius 0 before hatching.
  • Round a whole rectangle in one go with FILLET, P (polyline), then pick it (Radius first).
  • Extend to a boundary that is not touching using Edge > Extend.
  • Use Shift to flip between TRIM and EXTEND without leaving the command.

Common mistakes

  • Clicking the part of the line you want to keep in TRIM; you click the part to remove.
  • Picking the wrong side of a line in FILLET, which keeps the opposite end.
  • Leaving a non-zero fillet radius active and rounding a corner by accident (the radius is remembered).
  • Trying to trim an object with nothing crossing it in the current view or on a locked layer.

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. In TRIM, what do you click?

    You click the portion you want trimmed away.
  2. 2. What does FILLET with radius 0 do?

    Radius 0 makes a clean corner at the intersection.
  3. 3. Which key flips TRIM into EXTEND while the command is running?

    Hold Shift while picking to extend instead of trim, and vice versa.
  4. 4. A right-angle corner is filleted with radius 10. How far from the corner is each tangent point?

    d = r / tan(45 degrees) = 10.

Summary

  • TRIM removes the picked part against cutting edges; EXTEND lengthens to boundaries; Shift swaps them.
  • Select-all cutting edges makes quick trims; Fence and Crossing batch the work.
  • FILLET adds a tangent arc; radius 0 gives a sharp corner; Polyline mode rounds every vertex.
  • CHAMFER bevels with two distances or a distance and angle.
  • The settings are remembered, so reset radius and distances when switching tasks.

Next: OFFSET, MIRROR and Arrays