Skip to content
Tutorials Center
My learning

Topics

Lesson 37 of 38 ยท Projects and Practice

AutoCAD Project: Mechanical Part Drawing and 3D Model

Draw a flange plate in AutoCAD: bolt circle with POLAR ARRAY, 2D views, linear and diameter dimensions with tolerances, then a 3D solid with EXTRUDE and SUBTRACT, mass check and a layout sheet.

In this project you will draw a flange plate, a round steel part with a central hole and a ring of bolt holes, first as a 2D dimensioned drawing and then as a 3D solid. The part is simple on purpose, so you can focus on mechanical drafting habits: centerlines, a bolt circle, precision with object snaps, tolerances and mass.

AutoCAD cannot run on this site. Each step lists the commands to use, and the runnable examples are labelled JavaScript stand-ins that compute coordinates and mass so you can check your drawing. Confirm everything in AutoCAD with DIST, LIST and MASSPROP.

The part

  • Outside diameter: 140 mm. Thickness: 12 mm.
  • Central bore: 50 mm diameter, tolerance +0.05 / 0.
  • Six bolt holes, 11 mm diameter, on a 100 mm bolt circle, evenly spaced, the first at 0 degrees.
  • Edge chamfer: 1 mm x 45 degrees on the outside.
  • Material: mild steel, density 7,850 kg/m3.

Step 1: set up

  1. Use a metric template. UNITS: decimal, precision 0.00. Layers (see layers): OBJECT (continuous, 0.50 mm), HIDDEN (dashed, 0.25), CENTER (center linetype, 0.18), DIM (0.18), HATCH, TEXT, VPORT (no plot).
  2. Set LTSCALE to 1 for a drawing you will plot near 1:1 (raise it if the dashes look solid). In a 1:2 layout, use PSLTSCALE.

Step 2: the front view (2D)

  1. Layer CENTER: LINE a horizontal and vertical centerline crossing at 0,0, each 160 mm long, centered. Extend them 3 mm beyond the part, as drafting standards require.
  2. Layer OBJECT: CIRCLE at 0,0 radius 70 (outside), then radius 25 (bore).
  3. Draw one bolt hole: CIRCLE with center 50,0 radius 5.5. Use CENTER for the bolt circle: a circle of radius 50 at 0,0 on the CENTER layer.
  4. Pattern the hole: ARRAYPOLAR (ARRAY > Polar): select the hole, center point 0,0, items 6, angle to fill 360. The array is associative: change the item count in the contextual ribbon and every hole follows.
  5. Add the chamfer as a visible circle of radius 69 for the edge line in the front view.
JS Stand-in: bolt hole centre coordinates

Press Run (or Ctrl + Enter) to see the console output here.

No output.

Step 3: the section view

A side view shows the thickness and bore. Draw it to the right of the front view (use XLINE or projection lines at the hole edges, then TRIM):

  1. A rectangle 12 mm thick and 140 mm tall, centered on the same Y as the front view's center. Use RECTANGLE with two corners, or OFFSET the front view edges.
  2. The bore appears as two hidden lines (layer HIDDEN) or, in a section, as an opening. For a section, HATCH the cut material with ANSI31 at scale 1 and angle 0 (see hatches), leave the bore empty, and add a section line with arrows in the front view labelled A-A.
  3. Show the chamfer as a 1 mm x 45 degree cut on the corners with CHAMFER (distance 1, 1). Use FILLET radius 0 or CHAMFER on corners that must close.

Step 4: dimensions with tolerance

Create a dimension style MECH (see dimension styles): arrows 2.5, text 2.5 at 1:1, two decimals, Deviation tolerance. Then:

  • DIMDIAMETER on the outside circle: 140.
  • DIMDIAMETER on the bore with tolerance: select it and, in Properties, set Tolerance display: Deviation, upper +0.05, lower 0. Result: 50 +0.05/0.
  • DIMDIAMETER on one bolt hole and add the note 6X before it: Mtext 6X <> keeps the measurement. Add the bolt-circle diameter 100 as a reference (put it in brackets as reference with (100) if it is derived).
  • DIMLINEAR for the thickness 12 in the side view.
  • A geometric position tolerance with TOLERANCE for the bolt hole pattern if the course exercise requires it.
JS Stand-in: is a measured bore within tolerance?

Press Run (or Ctrl + Enter) to see the console output here.

No output.

Step 5: build the 3D model

  1. Switch to the 3D workspace (see 3D basics) and set UCS to World.
  2. CYLINDER at 0,0,0, radius 70, height 12.
  3. A second CYLINDER at 0,0,0 radius 25, height 12 and a bolt-hole cylinder at 50,0,0 radius 5.5, height 12. Make the cutters slightly taller if you like (13 mm from Z = -0.5 to 12.5), so the cuts pass cleanly through.
  4. ARRAYPOLAR the hole cylinder (6 items), or use 3DARRAY > Polar.
  5. SUBTRACT: select the large cylinder first (the keeper), press Enter, then the bore and the six bolt cylinders (see Booleans).
  6. CHAMFEREDGE 1 mm on the top outside edge.
  7. MASSPROP to read the volume and mass properties.
JS Stand-in: volume and mass of the flange

Press Run (or Ctrl + Enter) to see the console output here.

No output.

Step 6: layout

In a layout (A3 landscape) place three viewports: the front view at 1:1, the section at 1:1 and an isometric 3D view with the Hidden or Shaded visual style at 1:2. Lock them. Use VIEWBASE to produce 2D views from the 3D model if you prefer: base view (front), then projected views, set them to the part's layer scheme. Insert a title block, add a bill of materials table (one item: FLANGE-140, steel, qty 1, mass from MASSPROP) and plot to PDF.

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. Which command creates the six evenly spaced bolt holes from one?

    A polar array copies objects around a center point; with 6 items over 360 degrees they are 60 degrees apart.
  2. 2. What is the chord between neighbouring holes of a 6-hole pattern on a 50 mm radius?

    For six holes the chord 2 r sin(30 degrees) equals the radius, 50 mm.
  3. 3. In SUBTRACT, which solid do you select first for the flange?

    Select the solid to keep first, then the cutters.
  4. 4. How is a +0.05 / 0 tolerance on a bore set in a dimension?

    The dimension style or the dimension's Properties tolerance settings produce the limits and keep them associative.

Summary

  • Start with centerlines, then circles, then a polar array for repeated holes.
  • Show a section with hatching, and dimension with diameter symbols and tolerances.
  • Build the 3D solid with cylinders and SUBTRACT, finish with CHAMFEREDGE, and read MASSPROP.
  • Put views, a 3D view and a title block on one layout and plot a PDF.

Next: Practice: command quiz and exercises