Skip to content
Tutorials Center
My learning

Topics

Lesson 8 of 38 ยท Interface and Setup

Drafting Settings: Object Snap, Ortho, Polar and Grid

Place geometry exactly in AutoCAD: object snaps (endpoint, midpoint, center, intersection), running snaps, Ortho, Polar Tracking, Object Snap Tracking, Grid and Snap, with runnable snap math.

Clicking "near" a corner is never good enough in CAD. Drafting aids make the cursor jump to exact points: ends of lines, centres of circles, intersections, or multiples of an angle. They are the difference between a drawing that looks right and one that is right. This lesson covers each aid and how to set it in the Drafting Settings dialog (type DSETTINGS or right-click a status-bar button and choose Settings).

Object snaps (OSNAP)

An object snap makes AutoCAD pick an exact geometric point of an existing object. While a command asks for a point, hover over an object; a marker shows the snap type, and a tooltip names it. Click to accept.

Snap Marker Finds
Endpoint square ends of lines, arcs, polyline segments
Midpoint triangle middle of a line or arc
Center circle centre of circle, arc, ellipse
Geometric Center centroid of a closed polyline
Node point objects
Quadrant diamond 0/90/180/270 degree points of a circle
Intersection X where two objects cross
Extension dashes along the imaginary extension of a line
Insertion insertion point of text or block
Perpendicular foot of a perpendicular
Tangent tangent point on a circle or arc
Nearest the closest point on any object (not exact for location)
Apparent Intersection where two objects seem to cross, even in different planes
Parallel direction parallel to a line

Running snaps and overrides

There are two ways to use them:

  • Running object snaps stay on. Press F3 (the Object Snap toggle) and tick the types you want in settings. Do not enable all of them; too many markers clutter the screen and make the wrong one fire. Endpoint, midpoint, center, intersection and perhaps quadrant are a good everyday set.
  • Object snap overrides apply once. Hold Shift and right-click to open the snap menu, or type the three-letter code at a point prompt: END, MID, CEN, INT, PER, TAN, NEA, QUA. The override beats the running snaps for that pick only. Pressing Tab while hovering cycles through overlapping snap candidates.

Ortho (F8) and Polar Tracking (F10)

Ortho restricts movement to horizontal and vertical. Polar Tracking shows an alignment path at set angle increments (such as 90, 45, 30, 15 degrees) and snaps the cursor to it when you are near. Both work with direct distance entry. Ortho and Polar are mutually exclusive; turning on one turns the other off. Hold Shift to temporarily switch Ortho on or off. Set the increment angle and any additional angles (such as 22.5) in the Polar Tracking tab.

Object Snap Tracking (F11)

With Object Snap Tracking, you "acquire" a point by hovering over it (a small plus sign appears), then moving the cursor away to see a dotted alignment line. This lets you place a point that is, say, aligned horizontally with one endpoint and vertically with another, without drawing construction lines. It requires Object Snap to be on.

Grid and Snap (F7, F9)

Grid (F7) shows a field of dots or lines as a visual reference; it does not affect geometry. Snap Mode (F9) forces the cursor to jump in fixed steps (e.g. 100 units). Snap is useful for pixel-art-like layouts or electrical schematics but is rarely used in architectural or mechanical drawing, where object snaps and typed distances dominate. Beware: Snap Mode set to a large step makes it seem the cursor "jumps"; turn it off if you do not mean to use it.

Tips

  • Use TAB to cycle snap choices.
  • Pick the intersection of two crossing lines with INT rather than an endpoint if they overlap.
  • If a snap fails, zoom in: markers appear inside an aperture of a few pixels (APERTURE), so tight objects need more magnification.
  • Temporary tracking point (type TT at a point prompt) lets you start tracking from any point you click.

Stand-in: how an endpoint/midpoint snap picks

AutoCAD checks candidate snap points within a small pixel aperture and takes the closest. This stand-in does that for lines.

Python Stand-in: nearest snap point inside the aperture

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Stand-in: polar tracking

Polar tracking snaps to the nearest allowed angle when the cursor is within a tolerance (typically about 5 degrees).

Python Stand-in: Polar Tracking and Ortho

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Quick setup recipe

  1. Turn on Object Snap with running snaps for Endpoint, Midpoint, Center, Intersection and Quadrant.
  2. Turn on Polar Tracking at 90 degrees for rectilinear work (add 45 or 30 when needed).
  3. Turn on Object Snap Tracking.
  4. Keep Grid on for orientation, but Snap Mode off.
  5. Use Dynamic Input for distances.

Common mistakes

  • Enabling every snap, then getting the wrong point because markers overlap.
  • Picking "close enough" without a snap and creating tiny gaps that later break hatches and trims.
  • Leaving Snap Mode on with a large step.
  • Expecting snaps to work with object snap toggled off (F3).

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. Which object snap finds the point where two lines cross?

    Intersection (the X marker) finds crossing points of two objects.
  2. 2. Hold Shift and right-click does what?

    That menu lets you choose a one-time snap like Perpendicular or Tangent.
  3. 3. Ortho and Polar Tracking can both be on at the same time.

    They are mutually exclusive in the status bar.
  4. 4. What does Object Snap Tracking let you do?

    You acquire points by hovering and then place a new point along dotted alignment paths.

Summary

  • Object snaps give exact points on existing geometry; use a small running set plus overrides.
  • Ortho and Polar Tracking constrain direction; use them with direct distance entry.
  • Object Snap Tracking aligns new points with acquired ones.
  • Grid is visual; Snap Mode steps the cursor and is often off.
  • Always snap or type coordinates; never click by eye.

Next: LINE and Direct Distance Entry