Skip to content
Tutorials Center
My learning

Topics

Lesson 3 of 38 ยท Getting Started

Your First Drawing: Templates, Limits and Saving

Start a new AutoCAD drawing correctly: choose a DWT template, set units, understand drawing limits and scale factors, draw your first shapes and save with QSAVE and SAVEAS.

A good drawing starts before the first line. You choose a template, set units, and decide how big the drawing area should be. Then you draw a few shapes, check them, and save. This lesson walks through that sequence so every later drawing starts the same clean way.

Starting a new file

Press Ctrl+N (or the NEW command, or the "+" tab next to the drawing tabs). AutoCAD asks for a template: a .dwt file that carries settings so you do not rebuild them every time. Typical templates:

Template Use
acad.dwt imperial (feet/inches) 2D start
acadiso.dwt metric (millimetres) 2D start
acad3D.dwt / acadiso3D.dwt 3D modelling starts
your own .dwt company standards: layers, text styles, dimension styles, title blocks

A template stores units, layers, linetypes, text and dimension styles, layouts and even a title block. Teams spend real effort on a good template because it enforces consistency. You create one by setting up a drawing as you like it and using SAVEAS with file type "AutoCAD Drawing Template (*.dwt)". Templates live in the folder shown in OPTIONS > Files > Template Settings.

Set units first

Run UNITS and check length type, precision and the insertion scale (see Coordinates, Units and Precision). For a metric architectural plan you would choose Decimal, precision 0, millimetres. A template picked to match your discipline already has this.

Drawing limits and the "infinite" canvas

Old AutoCAD forced you to define LIMITS: a rectangle describing the paper. Modern model space is effectively unbounded; limits only matter if you turn limits checking on or want the grid to cover a specific area. What you should still think about is how large the drawing is relative to the sheet, because that sets text and dimension sizes.

The key relationship is the scale factor:

scale factor = 1 / drawing scale, for a plot at 1:50, the factor is 50.

A text that must be 2.5 mm tall on paper must be 2.5 x 50 = 125 units tall in model space if the drawing is in mm. Modern annotative objects handle this for you (Chapter 5), but the idea stays useful.

Your first shapes

With a metric template open, follow this exact sequence (commands go on the command line; press Enter after each entry):

  1. LINE, then 0,0, 4000,0, 4000,3000, 0,3000, C (C closes the shape back to the start). You have a 4 m by 3 m room outline.
  2. CIRCLE, then 2000,1500, then 300 for a table of radius 300.
  3. ZOOM, then E (Extents) to fit the view to your geometry. Mouse-wheel double click does the same.
  4. DIST, pick two corners to check the diagonal; it should read 5000.

Saving

AutoCAD gives you several ways:

  • QSAVE (Ctrl+S) saves under the current name. A never-saved drawing opens the Save As dialog.
  • SAVEAS (Ctrl+Shift+S) saves a copy with a new name, and lets you choose an older DWG version or a DXF/DWT file type.
  • Autosave writes a temporary .sv$ file every few minutes (SAVETIME, default 10 min) in a temp folder. It is for crash recovery, not a substitute for saving.
  • A .bak backup of the previous save sits beside your DWG when "Create backup copy with each save" is on.

Save early, name files meaningfully (house-ground-floor-v03.dwg), and keep a project folder structure.

Opening and closing

OPEN (Ctrl+O) loads a DWG; multiple drawings appear as tabs in the file tab bar, each with Model, Layout1, Layout2 tabs at the bottom. QUIT or the tab's X closes a drawing; AutoCAD asks to save if there are changes. The Start tab shows recent files and templates.

Stand-in: checking your first drawing

AutoCAD would tell you the diagonal with DIST and the area with AREA. This stand-in computes the same facts for the 4 m x 3 m room.

Python Stand-in: diagonal, area and perimeter of the room

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The shoelace formula in area is the same method a CAD kernel uses for closed polylines.

Stand-in: text height from scale

Python Stand-in: model-space text height for a plot scale

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

This is why a drawing printed at 1:100 needs text 100 times larger in model space than one printed at 1:1.

Habits for a clean start

  • Open the right template, never an arbitrary old drawing.
  • Save immediately under a proper name, then work.
  • Draw at full size near the origin.
  • Use ZOOM Extents often to make sure no stray object sits far away (a stray object makes zooming feel wrong and bloats plots).
  • Use the file-tab names to keep track of several open drawings.

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. What file extension does an AutoCAD drawing template have?

    DWT is the template format. DWG is a normal drawing, DXF an exchange format and BAK a backup.
  2. 2. A drawing in millimetres will be plotted at 1:50. What model-space height gives 2.5 mm text on paper?

    2.5 mm times the scale factor 50 equals 125 units.
  3. 3. What does the C option do at the end of a LINE sequence?

    Close joins the last point to the first and ends the command.
  4. 4. Which command saves a copy under a new name or older DWG version?

    SAVEAS lets you choose a new name and file type or version.

Summary

  • Start from a template (DWT) that matches your units and standards.
  • Set UNITS first; draw full size near the origin.
  • Scale factor = 1 / plot scale, and it sets model-space text size.
  • Use QSAVE often, SAVEAS for copies and versions; autosave is only a safety net.
  • Verify early with DIST, AREA and ZOOM Extents.

Next: DWG, DXF and Drawing Recovery