Skip to content
Tutorials Center
My learning

Topics

Lesson 2 of 38 ยท Getting Started

Coordinates, Units and Precision in AutoCAD

Master AutoCAD coordinate entry: absolute X,Y, relative @X,Y, polar @distance<angle>, the UCS, angle direction, and how to choose drawing units before you draw.

Every point in AutoCAD has a position, and you can type that position instead of clicking. Typing coordinates is how you get exact geometry, so this is the most important skill in the course. This lesson explains the coordinate systems, the three entry formats, angles, and drawing units.

The Cartesian plane

AutoCAD's 2D world is a plane with an X axis (horizontal, increasing to the right) and a Y axis (vertical, increasing upward). The point where they cross is the origin, (0,0). In 3D a Z axis points toward you out of the screen. The coordinate system that defines these axes is the World Coordinate System (WCS). You can create your own User Coordinate System (UCS) with the UCS command to move or rotate the axes; this is essential in 3D (Chapter 7).

Three ways to type a point

When a command asks "Specify first point:", you may type any of these:

Format Example Meaning
Absolute Cartesian 50,30 X = 50, Y = 30 from the origin
Relative Cartesian @20,10 20 right and 10 up from the last point
Relative polar @40<60 40 units away at an angle of 60 degrees from the last point

The @ sign means "relative to the last point you specified". With Dynamic Input on (Lesson Command Line and Dynamic Input), the @ is added for you on the second and later points, but typing it explicitly always works. A related format is #50,30, which forces an absolute entry when Dynamic Input would otherwise treat it as relative.

flowchart LR
    O["Origin (0,0)"] -->|"absolute 50,30"| P["P1 (50,30)"]
    P -->|"relative @20,10"| Q["P2 (70,40)"]
    Q -->|"polar @40 at 60 degrees"| R["P3 (90,74.6)"]

Each relative entry starts from the previous point, not from the origin.

Angles

By default AutoCAD measures angles counter-clockwise from the positive X axis (east = 0, north = 90, west = 180, south = 270). Negative angles go clockwise, so @10<-45 heads down and to the right. The UNITS command lets you change the base direction and make angles clockwise, but leave the defaults unless a project requires otherwise; mixing conventions is a classic source of errors.

Direct distance entry

With Ortho or Polar Tracking on, you can move the cursor in a direction and type just a number: Enter. AutoCAD uses that number as the distance along the cursor direction. It is the fastest way to draw rectilinear plans; see Line and Direct Distance Entry.

Choosing drawing units

AutoCAD is unitless inside: a line "100 units long" is only a number. You decide what one unit means: millimetres for mechanical parts, millimetres or metres for architecture, feet-and-inches for US imperial drawings. Decide before you start and be consistent, because inserting a drawing into another one scales by the unit ratio.

Run the UNITS command to set:

  • Length type: Decimal, Architectural (feet and fractional inches), Engineering, Fractional, Scientific.
  • Precision: how many decimals are displayed. Internally AutoCAD still stores about 14 significant digits, so a display of 0.00 does not round your geometry.
  • Angle type and precision: decimal degrees, deg/min/sec, radians, grads, surveyor units.
  • Insertion scale: the unit used when you insert blocks or images ("Millimeters", "Meters", "Inches").

Distance and angle between points

Once you can place points exactly, you can verify them. The DIST command reports the distance, angle in the XY plane, and the delta X, Y between two points. The stand-in below does the same arithmetic.

Python Stand-in: absolute, relative and polar entry

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Notice that the third result is computed from the second point (70, 40), exactly as the diagram showed.

DIST: distance, angle and deltas

Python Stand-in: what the DIST command reports

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Precision habits

  1. Never trust a point you placed by eye. Use snaps (Lesson Drafting Settings) or type coordinates.
  2. Draw near the origin. Very large coordinate values (survey data in the millions) reduce graphics precision; use UCS or shift the drawing.
  3. Keep units and the insertion scale consistent across all files in a project.

Common mistakes

  • Forgetting @, so the point is measured from the origin instead of the last point.
  • Typing a comma where the locale expects a list separator. Some regional settings use a semicolon list separator while AutoCAD still expects commas; if 5,10 fails, check the Windows list-separator setting.
  • Mixing up < (angle) with , (second coordinate).
  • Confusing display precision with stored precision.

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. What does the entry @20,10 mean?

    The @ sign makes the entry relative to the previous point.
  2. 2. In the default settings, which direction is an angle of 90 degrees?

    Angles are measured counter-clockwise from the positive X axis, so 90 degrees points up.
  3. 3. What do you get from the entry @10<-45 after the last point?

    A negative angle is clockwise from east, so the point lies down and to the right.
  4. 4. Setting UNITS precision to 0.00 will:

    Precision controls the display only. Stored geometry keeps full double-precision accuracy.

Summary

  • Points are X,Y (and Z in 3D) measured on the WCS or a custom UCS.
  • Use absolute x,y, relative @dx,dy and polar @dist<angle; # forces absolute.
  • Angles run counter-clockwise from east by default.
  • Pick a unit meaning (mm, m, in) per project and set it with UNITS.
  • DIST verifies what you drew.

Next: Your First Drawing: Templates, Limits and Saving