Skip to content
Tutorials Center
My learning

Topics

Lesson 10 of 38 ยท Drawing Commands

Circles, Arcs and Ellipses in AutoCAD

Draw circles by centre-radius, diameter, 2-point, 3-point and tangent options; use the eleven ARC methods; create ellipses; and see the geometry behind each option with Python stand-ins.

Round geometry appears in almost every drawing: holes, wheels, arches, rounded corners. AutoCAD gives you several ways to define circles and arcs depending on what information you have. Knowing which option fits the data you have saves a lot of construction work. This lesson covers CIRCLE, ARC and ELLIPSE, with Python stand-ins for the geometry underneath.

CIRCLE

Home > Draw > Circle (or C). Options:

Option You provide Typical use
Center, Radius centre point and radius holes, columns
Center, Diameter centre and diameter (type D) bores specified by size
2-Point two ends of a diameter fit between two points
3-Point three points on the circumference circle through three known points
Tan, Tan, Radius two tangent objects and a radius rounded fitting between two lines
Tan, Tan, Tan three tangent objects inscribed circle of a triangle

The command line prompt is Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:. Type the letters in brackets to switch method. For Ttr, hover over each of the two objects with the Tangent snap and then type the radius. Because there can be more than one circle that satisfies the rule, AutoCAD picks the one nearest the points where you clicked.

The CIRCLERAD system variable sets a default radius; the prompt shows it in angle brackets.

ARC: eleven ways

Arc is in the Draw panel drop-down, with these methods (named after the data you give, in order): 3-Point, Start-Center-End, Start-Center-Angle, Start-Center-Length (chord), Start-End-Angle, Start-End-Direction, Start-End-Radius, Center-Start-End, Center-Start-Angle, Center-Start-Length, and Continue (tangent to the last line or arc).

Two rules to remember:

  1. By default, arcs are drawn counter-clockwise from the start point to the end point. If your arc bulges the wrong way, swap start and end, or hold Ctrl while picking the end point to reverse the direction.
  2. The included angle is the arc's sweep. Positive angles are counter-clockwise.

For a quick, forgiving arc, use 3-Point. For a tangent arc at the end of a line, use Continue (or ARC, then Enter).

ELLIPSE

Home > Draw > Ellipse. Options: Axis, End (give one full axis by two points, then the distance for the other half axis), Center (centre, axis end, other axis distance), and Arc (an elliptical arc). AutoCAD makes a true ellipse object by default; the system variable PELLIPSE set to 1 creates a polyline approximation instead, which some tools prefer.

Geometry behind circle options

The 3-point circle is the circumscribed circle (circumcircle) of a triangle. Its centre is where the perpendicular bisectors of two chords meet. The stand-in computes it directly.

Python Stand-in: CIRCLE 3-Point, centre and radius

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

That last case is why AutoCAD cannot make a 3-Point circle through three points on one line.

Geometry behind arcs

An arc is stored as centre, radius, start angle and end angle. Given three points you can find its centre (as above) and compute angles; the sweep direction follows from the order. This stand-in converts a 3-point arc into stored form and gives length and sagitta (the arc's height over its chord).

Python Stand-in: ARC 3-Point to centre, angles and length

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The sweep is negative because the arc goes clockwise from start to end; AutoCAD stores an arc counter-clockwise, so internally it swaps the start and end angles.

Combining with other tools

  • Rounded rectangle corners: use FILLET (Chapter 4) instead of drawing arcs.
  • Concentric circles for a flange: draw one, then OFFSET or COPY with the centre as base.
  • A slot: two lines and two semicircle arcs (use Continue), or PLINE with arc segments (Lesson Polylines and Splines).

Common mistakes

  • Typing a diameter at a radius prompt. Check the prompt, or type D first.
  • Arcs that bulge the wrong way because of counter-clockwise rules.
  • Using Nearest snap on a circle and getting an unexact tangent point; use Tangent or Quadrant snaps.
  • Drawing a circle slightly off-centre because the centre was clicked without snap.

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. Which CIRCLE option needs two tangent objects and a number?

    Tan, Tan, Radius uses two tangent objects and a radius.
  2. 2. In which direction does AutoCAD draw arcs by default?

    Arcs run counter-clockwise from the start point to the end point unless you reverse with Ctrl.
  3. 3. How is a stored arc defined?

    Centre, radius and two angles define the arc.
  4. 4. Why does a 3-Point circle fail through three points on one straight line?

    Collinear points have no circumcircle; the radius would be infinite.

Summary

  • CIRCLE has Center-Radius/Diameter, 2P, 3P, Ttr and Ttt.
  • ARC has eleven methods; default direction is counter-clockwise; Ctrl reverses it.
  • ELLIPSE uses Axis-End, Center or Arc.
  • A 3-point circle is a triangle's circumcircle; arcs store centre, radius and two angles.

Next: Rectangles, Polygons and Regular Shapes