Skip to content
Tutorials Center
My learning

Topics

Lesson 30 of 38 · Interference and Diffraction

Young's Double-Slit Experiment

See how two narrow slits make bright and dark fringes, derive the fringe spacing formula y = λD/d, and use it to measure the wavelength of light.

In the early 1800s many scientists believed light was a stream of tiny particles. Thomas Young shone light through two close slits and saw a pattern of bright and dark stripes on a screen. Particles going straight through two slits would make just two bright bands. Stripes are exactly what you expect from waves interfering, so Young's experiment became strong evidence for the wave nature of light.

In this lesson you will see how the pattern forms, derive the formula for the stripe spacing, and use it to measure the wavelength of light.

The set-up

Light of a single color (monochromatic) first passes through one narrow slit, or comes from a laser, and then hits a barrier with two narrow, parallel slits a distance d apart. A screen stands a distance D beyond the barrier. Each slit acts as a new source of waves (a consequence of diffraction, covered in the next lesson), and the two sources are coherent because they come from the same wave front.

On the screen you see alternating bright fringes (maxima) and dark fringes (minima), evenly spaced near the centre.

flowchart LR
    A["Monochromatic<br/>light"] --> B["Double slit<br/>(separation d)"]
    B --> C["Two coherent<br/>sources"]
    C --> D["Screen at distance D<br/>bright and dark fringes"]

Light is split into two coherent waves that overlap on the screen.

Where are the bright fringes?

Consider a point on the screen at angle θ from the central line. The wave from the farther slit travels an extra distance. For D much larger than d, the two rays are almost parallel and the path difference is:

path difference = d sin θ

Constructive interference (a bright fringe) needs a whole number of wavelengths:

d sin θ = nλ, with n = 0, 1, 2, ...

  • n = 0 is the central maximum, directly opposite the middle of the slits. Both paths are equal.
  • n = 1 is the first bright fringe on either side, and so on.
  • Dark fringes lie midway: d sin θ = (n + ½)λ.

The fringe spacing formula

For small angles, sin θ ≈ tan θ ≈ y / D, where y is the distance along the screen from the centre. A bright fringe is at y = nλD / d. The fringe spacing (distance between neighbouring bright fringes, or neighbouring dark ones) is:

Δy = λD / d

This is the formula to remember. It says:

  • Longer wavelength (red) gives wider spacing than shorter wavelength (blue).
  • Slits closer together (smaller d) give wider spacing.
  • A screen farther away (larger D) gives wider spacing.

The formula Δy = λD/d assumes small angles (D ≫ d and fringes near the centre). It is not accurate far from the centre of the pattern.

Worked example

Red laser light of wavelength 650 nm passes through slits 0.25 mm apart. The screen is 3.0 m away. Find the fringe spacing.

  1. Convert to metres: λ = 650 × 10⁻⁹ m, d = 0.25 × 10⁻³ m.
  2. Δy = λD/d = (650 × 10⁻⁹ × 3.0) / (0.25 × 10⁻³) = 7.8 × 10⁻³ m.
  3. The fringes are about 7.8 mm apart, easy to measure with a ruler.

Measuring the wavelength

Turn the formula around: λ = Δy · d / D. In a lab you measure the distance across, say, 10 fringes with a ruler, divide by 10 to reduce error, and measure D with a tape and d from the slit data. The experiment is a very good example of how a small quantity (λ is under a micrometre) can be found from large ones (millimetres and metres).

Python Fringe spacing and wavelength calculator

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Simulating the whole pattern

For two ideal narrow slits the intensity on the screen follows I = I₀ cos²(π d sin θ / λ). (A real pattern is also modulated by the single-slit effect, which you will meet next.) The plot below shows the bands.

Python Intensity pattern for two ideal narrow slits

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

White light

If the source is white light, each color has its own λ and so its own spacing. The central maximum is white (all colors have n = 0 there), but the higher-order fringes are colored, red outermost, because red has the longest wavelength and so the widest spacing. The sharp dark fringes of a laser pattern are replaced by blurry colored edges.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. In a double-slit experiment, what happens to the fringe spacing if the slit separation d is doubled (other things equal)?

    Δy = λD/d, so doubling d halves the spacing.
  2. 2. Light of wavelength 500 nm passes through slits 0.20 mm apart onto a screen 4.0 m away. What is the fringe spacing?

    Δy = (500 × 10⁻⁹ × 4.0) / (0.20 × 10⁻³) = 1.0 × 10⁻² m = 10 mm.
  3. 3. Why is the central fringe in a white-light double-slit pattern white?

    At the centre the path difference is zero for every wavelength, so all colors are bright together.
  4. 4. Which type of source is needed to see clear fringes?

    Interference needs a constant phase relationship, which two slits illuminated by one wave front provide.

Summary

  • Two coherent slit sources give alternating bright and dark fringes on a screen.
  • Bright fringes satisfy d sin θ = nλ; the small-angle spacing is Δy = λD/d.
  • Longer wavelengths, closer slits and a farther screen all widen the pattern.
  • Measuring Δy, d and D gives the wavelength of the light.
  • White light gives a white centre and colored outer fringes.

Next: Diffraction: Single Slits and Gratings