Skip to content
Tutorials Center
My learning

Topics

Lesson 15 of 37 ยท Energy Sources

Energy, Power and Efficiency: The Basics

Learn the difference between energy and power, convert joules, watts and kilowatt-hours, and calculate efficiency and energy cost for common devices.

Energy runs everything from cell phones to cities, and choosing how to produce it is one of the biggest environmental decisions. Before comparing coal with wind, you need a common language: what energy is, how it is measured, and why every device wastes some of it. This lesson builds that language with worked examples.

Energy and power

Energy is the capacity to do work or to cause change. Its SI unit is the joule (J). Energy comes in forms: kinetic (motion), thermal (heat), chemical (fuel, food), electrical, nuclear, gravitational potential, and radiant (light).

Power is the rate of using or producing energy: P = E / t. The SI unit is the watt (W), defined as one joule per second.

It is common to confuse the two. A 100 W light bulb uses energy at a rate of 100 joules every second. A power plant of 1,000 MW can produce 1,000 megajoules every second. Energy is the amount; power is how fast.

Because the joule is small, larger units are common.

Unit Meaning In joules
kilojoule (kJ) one thousand joules 10ยณ J
megajoule (MJ) one million joules 10โถ J
gigajoule (GJ) one billion joules 10โน J
kilowatt-hour (kWh) 1 kW of power for 1 hour 3.6 ร— 10โถ J
tonne of oil equivalent (toe) energy in a tonne of crude oil, by convention about 4.19 ร— 10ยนโฐ J

The kilowatt-hour is the unit on electricity bills. It is an amount of energy (power ร— time): 1 kW ร— 3,600 s = 3,600,000 J = 3.6 MJ. A 2 kW kettle that runs for 3 minutes (0.05 h) uses 2 ร— 0.05 = 0.1 kWh.

Python Energy and power converter

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The kettle has a very high power but runs only briefly, so it does not use much energy. The heater is lower in power but runs for hours, so it uses more. This is a good example of why you must keep power and energy apart.

Cost and carbon of electricity

If electricity costs a given price per kWh, the cost is energy times price. The carbon emissions of electricity depend on how it is generated, so they differ by country and by hour. A typical way to show this is the carbon intensity, in kilograms of COโ‚‚ per kWh. Values from near zero (hydro, wind, nuclear) to about 1 kg per kWh (a coal-fired plant) occur in practice.

Python Cost and carbon of a household appliance

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The same appliance has a very different footprint depending on how its electricity is produced, which is why cleaning up the electricity supply reduces emissions from everything that plugs in.

Energy conversion and the laws of thermodynamics

The first law of thermodynamics (conservation of energy): energy cannot be created or destroyed, only converted from one form to another. The second law: in every conversion, some energy becomes spread-out, low-quality heat that is hard to use again. So no real machine can convert all of its energy input into useful work.

Efficiency tells you how much of the input becomes useful output:

efficiency = useful energy output รท total energy input (ร— 100 for a percentage)

Typical approximate efficiencies:

Device Approximate efficiency
Incandescent bulb (light) about 2-5 % (the rest is heat)
LED bulb about 30-50 %
Gasoline car engine about 20-30 %
Large electric motor about 90 % or more
Coal power plant about 33-40 %
Combined-cycle gas plant about 50-60 %
Solar panel (commercial) about 15-23 %
Condensing gas boiler about 90 % or more

These are rounded ranges; specific machines vary. Note that "wasted" energy is not destroyed: it leaves as heat, which is why a power plant needs cooling water or towers.

flowchart LR
    A["Fuel energy<br/>100 units"] --> B["Power plant<br/>(38 % efficient)"]
    B --> C["Electricity<br/>38 units"]
    B --> D["Waste heat<br/>62 units"]
    C --> E["Transmission and use"]

A Sankey-style sketch of energy flow in a power plant (illustrative numbers).

Efficiency in a chain

When devices are linked, efficiencies multiply. If a power plant is 38 % efficient, the grid delivers 93 % of the electricity it receives, and an electric heater turns 100 % of it into heat, then only 0.38 ร— 0.93 ร— 1.00 โ‰ˆ 0.35 (35 %) of the fuel energy ends up as heat in the room. A heat pump can deliver two to four units of heat for each unit of electricity it uses, because it moves heat rather than making it, so the overall chain can do better.

Python Efficiency chain

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The ratio for the heat pump is called the coefficient of performance (COP). Values depend on temperature outdoors, so the number 3 here is only an example.

Energy quality, primary and final energy

Primary energy is the energy in natural sources before conversion (coal in the ground, sunlight, uranium). Final energy is what reaches the user (electricity at the socket, petrol in the tank). Useful energy is what actually does the job (light, motion, warmth). Each step loses some. This is why statistics for different fuels must be compared carefully, since electricity from wind has no conversion loss in some accounting methods and a large one in others.

A related measure is energy return on investment (EROI): the energy delivered by a source divided by the energy spent to get it. High EROI sources give more net energy. EROI values depend on assumptions and are debated, so use them as a qualitative idea here.

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. A 500 W appliance runs for 4 hours. How much energy does it use?

    Energy = power ร— time = 0.5 kW ร— 4 h = 2 kWh.
  2. 2. Which statement about the second law of thermodynamics is correct?

    Energy is conserved (first law), but conversions always spread some of it as heat that is hard to reuse (second law).
  3. 3. A plant takes in 500 MJ of fuel energy and produces 150 MJ of electricity. What is its efficiency?

    150 รท 500 = 0.30, which is 30 %.
  4. 4. How many joules are in 1 kWh?

    1 kW ร— 3,600 s = 3,600,000 J (3.6 MJ).

Summary

  • Energy (joules, kWh) is an amount; power (watts) is the rate. 1 kWh = 3.6 MJ.
  • Efficiency = useful output รท input; chain efficiencies multiply.
  • The second law means some energy always ends up as low-quality heat.
  • Carbon emissions of electricity depend on the generating mix, measured as kg COโ‚‚ per kWh.
  • Primary, final and useful energy differ; heat pumps can exceed 100 % "efficiency" because they move heat.

Next: Fossil Fuels: Coal, Oil and Natural Gas