Skip to content
Tutorials Center
My learning

Topics

Lesson 5 of 38 · Getting Started

Measurement, Units and Significant Figures

Master SI units and prefixes, convert units with dimensional analysis, and report calculated answers with the right number of significant figures.

Stoichiometry is a calculation subject. Every answer you compute starts from measured numbers, so you need three habits: using consistent units, converting between units carefully, and reporting answers with an honest number of digits. This lesson sets those habits up so the later calculations are clean.

SI units for chemistry

Science uses the International System of Units (SI). The ones you will meet most:

Quantity SI unit Symbol Common chemistry unit
Mass kilogram kg gram (g)
Length meter m centimeter, nanometer
Time second s
Temperature kelvin K degree Celsius (°C)
Amount of substance mole mol
Volume cubic meter m³ liter (L), milliliter (mL)
Pressure pascal Pa kilopascal (kPa), atmosphere (atm)

Prefixes scale a unit by powers of ten:

Prefix Symbol Factor
kilo k 10³
centi c 10⁻²
milli m 10⁻³
micro µ 10⁻⁶
nano n 10⁻⁹

So 1 kg = 1000 g, 1 g = 1000 mg, and 1 L = 1000 mL. Temperature in kelvin is T(K) = t(°C) + 273.15. Gas calculations later in the track must use kelvin.

Dimensional analysis

Dimensional analysis (also called the factor-label method) converts units by multiplying by fractions equal to 1. Each fraction is a conversion factor, written so that the unit you want to remove cancels.

Convert 2.50 L to mL. The relation is 1 L = 1000 mL, so the factor is 1000 mL / 1 L:

2.50 L × (1000 mL / 1 L) = 2500 mL

The unit "L" cancels, leaving mL. If your units do not cancel to the unit you want, you have the factor upside down. Mole calculations use exactly this method: molar mass is just a conversion factor between grams and moles.

Python Chain conversion factors

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Significant figures

A measurement is never perfectly exact. Significant figures (sig figs) are the digits that carry meaning: all the certain digits plus one estimated digit. A balance reading 12.35 g has four sig figs; the last digit is uncertain.

Rules for counting:

  1. Non-zero digits are always significant. 4.37 has three.
  2. Zeros between non-zero digits are significant. 1005 has four.
  3. Leading zeros are never significant; they only place the decimal point. 0.0042 has two.
  4. Trailing zeros after a decimal point are significant. 2.500 has four.
  5. Trailing zeros in a whole number without a decimal point are ambiguous. Write 1.20 × 10³ to show three sig figs.
  6. Exact numbers (counts like 12 eggs, or defined conversions such as 1000 mL = 1 L) have unlimited sig figs.

Sig figs in calculations

  • Multiplying or dividing: the answer has as many sig figs as the measurement with the fewest. 4.56 × 1.4 = 6.384, which you report as 6.4 (two sig figs).
  • Adding or subtracting: the answer has as many decimal places as the measurement with the fewest decimal places. 12.11 + 0.3 = 12.41, reported as 12.4.
  • Round only at the end. Keep extra digits in your calculator or program during the steps, then round the final answer once.
Python Round to significant figures

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

In this track, we usually give data to three or four significant figures and round final answers to match. The exact atomic masses on the periodic table are given to more digits than most data, so they should never be the limiting factor.

Accuracy and precision

Accuracy is how close a result is to the true value. Precision is how close repeated measurements are to each other. A scale that always reads 0.5 g too high is precise but not accurate. Good chemistry needs both.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. How many significant figures are in 0.00450?

    Leading zeros are not significant. The digits 4, 5 and the trailing 0 after the decimal point are significant: three.
  2. 2. Convert 3.2 L to mL.

    3.2 L × 1000 mL/L = 3200 mL.
  3. 3. What is 2.50 × 3.1 reported with correct sig figs?

    3.1 has two sig figs, so the product is rounded to two: 7.8.
  4. 4. What is 37 °C in kelvin?

    K = 37 + 273.15 = 310.15, which is about 310 K.

Summary

  • Use SI units and prefixes; temperature must be in kelvin for gas laws.
  • Convert units by multiplying by conversion factors so that unwanted units cancel.
  • Count significant figures with the zero rules; multiplication keeps the fewest sig figs, addition the fewest decimal places.
  • Round only at the end of a calculation.

Next: Reading Chemical Equations