Skip to content
Tutorials Center
My learning

Topics

Lesson 24 of 39 · Forces and Newton's Laws

Friction and Inclined Planes

Learn static and kinetic friction, the coefficient of friction, and how to solve inclined-plane problems with components, critical angles and a short simulation.

Without friction you could not walk, drive or even hold a pencil. With it, every sliding object eventually stops. Friction is a contact force that acts parallel to the surfaces and opposes (or prevents) sliding between them. In this lesson you will learn a simple model of friction and use it on one of the best-loved problems in mechanics: the inclined plane.

Two kinds of friction

Static friction acts when the surfaces are not sliding. It adjusts itself to match the push, up to a maximum:

f_s ≤ μ_s · N

Push a heavy box gently and static friction is small and equal to your push, so nothing moves. Push harder and it grows, until it hits its limit μ_s·N. After that the box starts to slide.

Kinetic friction acts while the surfaces slide. It has a nearly constant size:

f_k = μ_k · N

The symbols μ_s and μ_k (Greek "mu") are the coefficients of friction. They are pure numbers with no units that depend on the pair of surfaces. For most pairs μ_k is a bit smaller than μ_s, which is why it is easier to keep a box moving than to start it.

Typical values (approximate, they vary with conditions): rubber on dry concrete μ_s ≈ 0.8–1.0; wood on wood ≈ 0.3–0.5; steel on ice ≈ 0.03.

Friction depends on the normal force N, not directly on the weight, and (in this simple model) not on the contact area. Friction is also not always "bad": it is the force that accelerates a walking person or a car.

Python Does the box move?

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Inclined planes

A block sits on a ramp that makes angle θ with the horizontal. Choose axes along the ramp (x, down-slope positive) and perpendicular to it (y). Only the weight is slanted, so split it:

  • Component along the ramp: mg sin θ (down-slope).
  • Component into the ramp: mg cos θ.
flowchart TD
    W["Weight mg"] --> P["Parallel part: mg sin(theta), down the slope"]
    W --> Q["Perpendicular part: mg cos(theta), into the slope"]
    Q --> N["Normal force N = mg cos(theta)"]
    N --> F["Kinetic friction = mu_k N, up the slope"]

Splitting the weight on a ramp. The normal force balances the perpendicular part.

Perpendicular to the ramp there is no acceleration, so N = mg cos θ. Along the ramp:

  • Frictionless: a = g sin θ.
  • With kinetic friction (block sliding down): m·a = mg sin θ − μ_k·mg cos θ, so

a = g (sin θ − μ_k cos θ)

The mass cancels, so the acceleration does not depend on how heavy the block is.

Example 1: sliding down

A block slides down a 30° ramp with μ_k = 0.2. Then sin 30° = 0.5 and cos 30° = 0.866:

a = 9.81 × (0.5 − 0.2 × 0.866) = 9.81 × 0.3268 ≈ 3.21 m/s²

Example 2: the critical angle

At rest on a ramp, static friction must equal mg sin θ, up to the limit μ_s·mg cos θ. The block just starts to slip when mg sin θ = μ_s·mg cos θ, i.e.

tan θ_c = μ_s

This gives a neat way to measure μ_s: tilt a board until the object slips, and take the tangent of that angle. For μ_s = 0.5, θ_c = arctan 0.5 ≈ 26.6°.

Python Acceleration down a ramp

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Pushing up the ramp

If a block slides up a ramp, kinetic friction points down the slope, adding to the gravity component: deceleration a = g (sin θ + μ_k cos θ) (down-slope, so the block slows). For the same 30° ramp and μ_k = 0.2, this is 9.81 × (0.5 + 0.1732) ≈ 6.60 m/s².

Air resistance in a nutshell

Moving through a fluid produces drag, which grows with speed. Falling objects speed up until drag equals weight; then the net force is zero and the speed stays constant at the terminal velocity. A skydiver in a spread-eagle position reaches roughly 50-55 m/s; in a head-down dive, much more. Drag needs a more detailed model, so in most introductory problems it is ignored unless stated.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. A 10 kg box on a level floor has μ_s = 0.5. About how large a horizontal push is needed to start it sliding?

    N = mg = 98.1 N, so max static friction = 0.5 × 98.1 ≈ 49 N. A push larger than this starts the motion.
  2. 2. Which statement about kinetic friction is correct (simple model)?

    f_k = μ_k N. In the basic model it does not depend on contact area or speed.
  3. 3. A block slides down a frictionless 30° ramp. What is its acceleration?

    a = g sin 30° = 9.81 × 0.5 ≈ 4.91 m/s², independent of mass.
  4. 4. A block just starts to slip at 35° on a board. What is μ_s approximately?

    At the critical angle tan θ = μ_s, so μ_s = tan 35° ≈ 0.70.

Summary

  • Static friction matches the applied push up to μ_s·N; kinetic friction is μ_k·N.
  • Coefficients of friction are unitless and depend on the two surfaces.
  • On a ramp: N = mg cos θ, and the down-slope pull is mg sin θ.
  • Sliding down with friction: a = g (sin θ − μ_k cos θ); the mass cancels.
  • The critical angle for slipping satisfies tan θ = μ_s.

Next: Work and the Work-Energy Theorem