Skip to content
Tutorials Center
My learning

Topics

Lesson 11 of 37 ยท Modelling

Loop Cuts and Edge Flow

Learn loop cuts, edge slide, quads versus triangles and n-gons, poles, and edge flow so your Blender models subdivide and deform cleanly.

Two models can look identical in a render and behave very differently when you subdivide or animate them. The difference is topology: how vertices, edges and faces are arranged. Good topology has even quads and edges that follow the shape. This lesson introduces loop cuts and the rules of clean edge flow.

Loop Cut and Slide (Ctrl+R)

A loop cut adds a ring of new edges around an object, cutting through a row of faces.

  1. In Edit Mode, press Ctrl+R and hover over an edge. A pink preview line shows where the loop will go.
  2. Scroll the wheel to make several cuts at once (or use the Adjust Last Operation panel: Number of Cuts).
  3. Click to confirm the number, then move the mouse to slide the loop along the surface (or press right-click to leave it centred).
  4. Use the Adjust Last Operation panel to set Edge Slide factor and Smoothness.

Loop cuts work only where faces are quads arranged in loops. If the preview does not show, the geometry between has a triangle or n-gon that stops the loop.

Edge slide (G G)

Press G twice with an edge selected to slide it along neighbouring edges without leaving the surface. It keeps the shape intact while tuning where edges sit.

Python Stand-in: a loop cut splits quads

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Quads, triangles and n-gons

Face type Verdict
Quad (4 sides) Preferred: subdivides evenly, supports loop cuts, deforms well
Triangle Fine on flat surfaces and hidden areas; the final game engine uses triangles anyway
N-gon (5+ sides) Acceptable on flat faces, a problem on curved or animated surfaces

The rule of thumb: keep quads where the surface bends or moves, and allow triangles or n-gons only on flat, static parts. A model with many n-gons can shade strangely when subdivided.

Poles

A pole is a vertex where other than four edges meet. A vertex with three edges (a 3-pole) or five (a 5-pole) is unavoidable when changing direction of flow. Poles are fine in flat areas, but avoid placing them where the surface curves sharply (cheeks, knees), because they pinch under subdivision.

Python Stand-in: find poles in a mesh

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Edge flow

Edge flow is the direction edges run across the surface. Good flow:

  • Follows the form and the way the object bends. On a face, loops circle the eyes and mouth; on a limb they wrap around it.
  • Is evenly spaced, so faces are roughly square, not long and thin.
  • Has support loops: extra edges near a corner keep it sharp when subdivided (an alternative to the bevel modifier).
  • Ends in poles only where necessary and in unobtrusive places.
flowchart LR
  A["Plan the shape"] --> B["Place loops along<br/>form and bending"]
  B --> C["Keep faces as quads"]
  C --> D["Add support loops<br/>at sharp edges"]
  D --> E["Test with a subdivision modifier"]

Check topology by turning on a subdivision surface and looking for pinches or creases.

Tools to improve topology

  • Dissolve edges (Ctrl+X) removes a loop while keeping the shape.
  • Merge (M) and Collapse reduce vertices.
  • Knife (K) and Connect Vertex Path (J) add edges where you need them.
  • Rotate Edge and Triangulate to Quads (Alt+J) adjust triangle pairs.
  • Offset Edge Slide (Shift+Ctrl+R) adds two loops around a selected edge to hold its sharpness.
  • Mirror and Subdivision modifiers reduce how much you need to model manually.

Planning loops: counting

A useful skill is predicting how many faces a loop cut makes. Cutting a cube's side ring doubles the rows; each cut in an N-sided ring adds N edges and N vertices.

Python Stand-in: count faces of a subdivided grid

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. What is the shortcut for Loop Cut and Slide?

    Ctrl+R in Edit Mode previews and adds a loop cut.
  2. 2. Which face type is preferred on curved or animated surfaces?

    Quads subdivide evenly and deform predictably.
  3. 3. What is a pole?

    Poles have three, five or more edges; keep them out of sharply curved regions.
  4. 4. What does G G do on a selected edge?

    Pressing G twice slides along neighbouring edges.

Summary

  • Ctrl+R adds loop cuts; slide them to position edges.
  • Prefer quads on curved or moving surfaces; triangles and n-gons suit flat static areas.
  • Poles redirect flow; place them where the surface is flat.
  • Good edge flow follows the form, has even spacing and uses support loops.

Next: Modifiers: Subdivision, Mirror and More