Skip to content
Tutorials Center
My learning

Topics

Lesson 25 of 37 ยท Animation and Rigging

Blender Armatures, Bones and Weight Painting for Rigging

Rig a model in Blender: add an armature, build a bone chain, parent with automatic weights, fix deformation with weight painting and pose the rig.

To animate a character, creature or flexible object you give it a skeleton. In Blender this is an armature: a special object made of bones. When you move a bone, the mesh vertices it controls follow. Setting this up is called rigging, and how strongly each bone pulls each vertex is called its weight.

Blender cannot run here, so this lesson lists the steps and menus precisely, and uses Python stand-ins to show the weighted-average maths behind skinning.

Adding an armature

  1. In Object Mode press Shift+A and choose Armature > Single Bone. A bone appears at the 3D cursor.
  2. Open the Object Data (green stick figure) tab. Enable Viewport Display > In Front so the bones show through the mesh.
  3. Press Tab to enter Edit Mode. Select the bone tip (the pointed end) and press E to extrude a new bone from it. Repeat to build a chain, for example upper arm, forearm, hand.
  4. Name every bone (Bone tab > Name) with a consistent suffix: arm.L, arm.R. Names ending in .L and .R let Blender mirror poses.

Useful edit-mode keys: G move, R rotate, S scale, Shift+E extrude with symmetry (turn on X-Axis Mirror in the Object Data tab), Alt+P to clear parents, Ctrl+P to connect.

A bone has a head (root, where it rotates) and a tail (tip). Child bones inherit the parent's movement, which creates a hierarchy.

The three modes

Mode Use Switch
Object Mode Move the whole armature default
Edit Mode Build and place bones (changes the rest pose) Tab
Pose Mode Rotate bones to animate Ctrl+Tab with the armature selected

In Pose Mode, you rotate (R) and move (G) bones, then press I to keyframe them. Bone rotation is stored relative to the rest pose built in Edit Mode, so clear it with Alt+G (location), Alt+R (rotation) and Alt+S (scale) to return to rest.

Skinning: parenting mesh to bones

To make the mesh follow the bones:

  1. In Object Mode select the mesh, then Shift-select the armature (the armature must be active, so click it last).
  2. Press Ctrl+P and choose With Automatic Weights.

Blender computes how much each bone influences each vertex and adds an Armature modifier to the mesh, plus one Vertex Group per bone. Other options: With Empty Groups (make groups to paint manually), With Envelope Weights, Armature Deform (bones only).

For good results, the mesh should have clean topology and enough edge loops at joints (elbows, knees) to bend. Apply scale (Ctrl+A > Scale) before rigging, since unapplied scale gives odd deformation.

How weights work

Each vertex has a weight between 0 and 1 for each bone. When bones move, the vertex position is the weighted sum of where each bone would place it (linear blend skinning). Weights should add up to 1. A vertex in the middle of an elbow might be 50 percent upper arm and 50 percent forearm, so it moves halfway.

Python Stand-in: linear blend skinning of one vertex

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

You can see the well-known "candy wrapper" problem: at 0.5 the vertex ends up closer to the pivot, so the mesh pinches in the middle of a twist. More edge loops and better weights reduce it.

Weight painting

If automatic weights are not good, fix them:

  1. Select the mesh, then switch to Weight Paint mode from the mode drop-down, or press Ctrl+Tab when a mesh and armature are linked in pose mode.
  2. In the Object Data tab > Vertex Groups, click a group (for example forearm.L) to see its weights as a heat map: red = 1, green/yellow = middle, blue = 0.
  3. Use the Draw brush with Weight 1.0 to add influence, Subtract to remove, Smooth to blend. Set Strength low (0.1 to 0.2) and paint in strokes.
  4. Useful commands: Weights > Normalize All, Limit Total (max 4 influences per vertex, a common game-engine limit), Clean, and Mirror (symmetrical rigs).

To test, enter Pose Mode on the armature, rotate bones and watch the mesh. Rotating a joint to extreme angles is a quick quality test.

Python Stand-in: normalize weights and limit influences

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Bone hierarchy and rig tips

flowchart TD
  R["root"] --> H["hips"]
  H --> S["spine"]
  S --> C["chest"]
  C --> A["upper_arm.L"]
  A --> F["forearm.L"]
  F --> HD["hand.L"]
  H --> T["thigh.L"]
  T --> SH["shin.L"]

A simplified character hierarchy: moving the hips moves everything below them.

  • Keep a single root bone so the whole character can be moved.
  • Blender includes the Rigify add-on (Preferences > Add-ons) that builds a full human rig from a template (Add > Armature > Human (Meta-Rig), then Generate Rig).
  • For rigid objects (robots, mechanical parts) skip weight painting: parent each part to a bone with Bone parenting (Ctrl+P > Bone), which makes it follow with 100 percent weight.
  • Related deformation tools: shape keys and constraints.

Common mistakes

  • Selecting the armature first, then the mesh, so the parent goes the wrong way.
  • Building bones in Pose Mode (nothing changes) or scaling bones in Edit Mode after skinning.
  • A rig with unapplied scale or negative scale.
  • Weights that do not add to 1 near joints; use Normalize All.

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. Which mode do you use to build and place bones?

    Edit Mode changes the rest pose, while Pose Mode only moves bones for animation.
  2. 2. In what order do you select objects before using Ctrl+P > With Automatic Weights?

    The child (mesh) is selected first and the parent (armature) must be the active object.
  3. 3. What does a vertex weight of 0.5 for a bone mean?

    Weights mix bone influences; 0.5 means half of the movement comes from that bone.
  4. 4. In the weight paint heat map, which color means full influence?

    Red means weight 1.0, blue means 0.

Summary

  • An armature is a skeleton of bones; build it in Edit Mode and pose it in Pose Mode.
  • Parent a mesh with automatic weights, then refine in Weight Paint mode.
  • Weights per vertex should sum to 1; limit influences for game engines.
  • Use consistent .L/.R names and a single root bone.

Next: Shape Keys and Constraints