Skip to content
Tutorials Center
My learning

Topics

Lesson 3 of 37 · Getting Started

Measuring Length and Angles

Learn metric length units, how to convert them, how degrees measure angles, how to use a protractor, and a short introduction to radians.

Measuring is where geometry meets the real world. To say "this table is long" is vague. To say "this table is 1.8 meters long" lets a carpenter build another one. In this lesson you will learn the standard units for length and angle, how to convert between them, and how to read a ruler and a protractor properly.

Length and the metric system

Most of the world uses the metric system (SI). Its base unit of length is the meter (m). Other units are made by multiplying or dividing by powers of ten:

Unit Symbol In meters
Millimeter mm 0.001 m
Centimeter cm 0.01 m
Meter m 1 m
Kilometer km 1000 m

So 1 m = 100 cm = 1000 mm, and 1 km = 1000 m. To convert, ask whether the number should get bigger or smaller. Changing to a smaller unit gives a bigger number (2.5 m = 250 cm) and the reverse is also true (350 mm = 35 cm).

The US customary system uses inches, feet, yards and miles. The key exchange rate is exact: 1 inch = 2.54 cm. From it, 1 foot = 12 inches = 30.48 cm.

Python A small length converter

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Reading a ruler

Line up the zero mark (not the edge of the ruler, which is sometimes slightly before it) with one end of the object. Read the mark at the other end. On a centimeter ruler the small marks are millimeters, so a length ending four small marks past the 7 cm mark is 7.4 cm. Always write the unit.

Measurements are never exact. A ruler marked in millimeters lets you give a length to the nearest millimeter, so a result such as 7.4 cm really means "between 7.35 and 7.45 cm".

Measuring angles

An angle is formed by two rays (its sides) that share an endpoint (the vertex). The size of the angle is the amount of turning from one side to the other. The standard unit is the degree (°). One full turn is 360°. That number was chosen by ancient astronomers and is handy because it divides evenly by so many numbers.

  • A quarter turn is 90° (a right angle).
  • A half turn is 180° (a straight angle).
  • A full turn is 360°.

Using a protractor

  1. Put the protractor's center hole exactly on the vertex.
  2. Line up the baseline (the 0° line) with one side of the angle.
  3. Read the scale where the other side crosses it. There are two scales, so choose the one that starts at 0° on the side you aligned. If the angle looks smaller than 90°, your answer should be smaller than 90°.

That last check catches the most common mistake: reading the wrong scale.

Before measuring, estimate. Is the angle smaller than a square corner (90°)? About half a square corner (45°)? Your estimate tells you if your reading is sensible.

Radians (a preview)

Mathematicians and programmers often use another unit, the radian. One full turn is 2π radians, so 180° = π radians. To convert: multiply degrees by π/180 to get radians, and multiply radians by 180/π to get degrees. Most programming languages' trigonometry functions expect radians.

Direction of an angle in code

If you know two points, you can find the direction of the line joining them. The function atan2(dy, dx) returns the angle in radians, measured counterclockwise from the positive x-axis. Subtracting two such directions gives the angle between two rays.

Python Angle between two rays

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The angle BVC comes out as 45°, which makes sense: B points straight up and C points halfway between up and left.

Degrees, minutes and seconds

For very fine measures, such as on maps and in navigation, one degree is split into 60 minutes (′) and one minute into 60 seconds (″). So 30.5° = 30° 30′. Most schoolwork uses decimal degrees instead.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. How many centimeters are in 3.2 meters?

    1 m = 100 cm, so 3.2 × 100 = 320 cm.
  2. 2. Exactly how many centimeters are in one inch?

    The inch is defined as exactly 2.54 centimeters.
  3. 3. An angle looks a little smaller than a square corner. Your protractor reading is 128°. What is the likely mistake?

    128° + 52° = 180°. An angle smaller than 90° cannot be 128°, so the other scale was read.
  4. 4. How many radians equal 180°?

    A half turn is 180° = π radians; a full turn is 2π.

Summary

  • The meter is the SI unit of length; units differ by powers of ten (1 m = 100 cm = 1000 mm; 1 in = 2.54 cm exactly).
  • Moving to a smaller unit gives a bigger number, and the reverse.
  • Angles are measured in degrees: right angle 90°, straight angle 180°, full turn 360°.
  • On a protractor, put the center on the vertex, align the baseline, and sanity-check the scale you read.
  • Radians measure the same turning: 180° = π radians; code uses radians.

Next: Reading Diagrams and Drawing with Code