Skip to content
Tutorials Center
My learning

Topics

Lesson 24 of 37 · Water and the Atmosphere

Groundwater and Aquifers

Learn how rain soaks underground, what porosity and permeability mean, how aquifers and wells work, and how to estimate groundwater flow with Darcy's law.

Beneath your feet, water fills tiny spaces in soil and rock. This groundwater is the largest source of liquid fresh water on land and supplies drinking water and irrigation for billions of people. It feeds springs, keeps rivers flowing in dry seasons and slowly moves through the ground. It is the "infiltration" arrow of the water cycle in detail.

Porosity and permeability

Two properties explain how rock holds and moves water:

  • Porosity is the percentage of a material's volume that is empty space. Clay can have high porosity but its pores are tiny.
  • Permeability is how easily water flows through the connected pores. Gravel and clean sand are highly permeable; clay and unfractured granite are not.

High porosity does not guarantee high permeability. Clay holds a lot of water and releases it very slowly because its pores are small and the water clings to the grains.

The water table and zones

Water soaking down eventually reaches material where every pore is full. The top of that saturated zone is the water table.

  • Unsaturated (vadose) zone: pores hold both air and water, above the water table.
  • Saturated zone: all pores filled with water, below the water table.

The water table is not flat: it tends to follow the shape of the land, higher under hills and meeting the surface at rivers, lakes and wetlands. It also rises after rainy seasons and falls in dry ones.

Aquifers and confining layers

An aquifer is a body of rock or sediment that holds enough connected water and lets it flow well enough to supply wells and springs. Sand, gravel, sandstone, fractured rock and some limestones are good aquifers. An aquitard (or confining layer), such as clay or shale, slows water down.

  • Unconfined aquifer: open to the surface; its upper boundary is the water table.
  • Confined aquifer: trapped between aquitards. The water is under pressure, so in a well that taps it the water level can rise above the top of the aquifer. If it rises above the ground, it flows freely: an artesian well.
flowchart TB
    S["Rain and infiltration"] --> U["Unsaturated zone"]
    U --> W["Water table"]
    W --> A["Unconfined aquifer"]
    A --> C["Confining layer (clay)"]
    C --> Q["Confined aquifer under pressure"]

A simplified vertical arrangement from the surface downward.

Wells, springs and problems

A well is a hole that reaches below the water table. Pumping lowers the water level around it in a funnel shape called a cone of depression. Too many wells pumping too fast can lower the whole water table.

A spring forms where the water table meets the surface, for example at the base of a hillside.

Common problems:

  • Overpumping: wells dry up; in some regions the ground itself sinks (subsidence) because the emptied sediment compacts.
  • Contamination: fertilizers, fuel and waste can seep down; because groundwater moves slowly, pollution can persist for years.
  • Saltwater intrusion: near coasts, heavy pumping can pull salty seawater into fresh aquifers.
  • Sinkholes: in limestone regions (karst), dissolution creates caves, and the roof can collapse.

Darcy's law

In the 1850s, the French engineer Henry Darcy found by experiment that the flow of water through sand depends on the pressure difference and on the material. In modern notation:

Q = K × A × (Δh / L)

  • Q: flow rate (m³/s)
  • K: hydraulic conductivity (m/s), how easily the material transmits water
  • A: cross-sectional area of the flow (m²)
  • Δh / L: the hydraulic gradient, the drop in water level per unit horizontal distance (unitless)

The average speed of the water in the pores is the seepage velocity v = (K × Δh / L) / n, where n is porosity, because the water is squeezed into a fraction of the cross-section.

Typical hydraulic conductivity: clean gravel about 10⁻² m/s, clean sand about 10⁻⁵ to 10⁻³ m/s, silt about 10⁻⁹ to 10⁻⁶ m/s, clay about 10⁻¹¹ to 10⁻⁹ m/s.

Python Darcy's law: flow through an aquifer

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The seepage speed is only a fraction of a meter per day, which is why contaminated groundwater is so hard to clean: the water does not flush out quickly.

Python Compare materials: how fast does water move?

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. The top of the saturated zone is called the

    Below the water table every pore is full of water.
  2. 2. Which material is most likely to be a good aquifer?

    Sand and gravel have connected pores, so water moves through them easily.
  3. 3. In Darcy's law, what does K represent?

    K measures how easily the material transmits water.
  4. 4. What happens when too many wells pump near a coast?

    Lower fresh water levels allow saltwater to be drawn inland (saltwater intrusion).

Summary

  • Groundwater fills pores below the water table; porosity is storage, permeability is flow.
  • Aquifers hold usable water; aquitards slow it. Confined aquifers can produce artesian wells.
  • Overpumping, contamination, saltwater intrusion and sinkholes are major problems.
  • Darcy's law: Q = K A (Δh / L); seepage velocity is the Darcy velocity divided by porosity.

Next: The Atmosphere: Layers and Composition