Skip to content
Tutorials Center
My learning

Topics

Lesson 12 of 37 ยท Plate Tectonics

Earthquakes, Faults and Magnitude

Understand why earthquakes happen, the three types of fault, how magnitude and intensity differ, and how much more energy each magnitude step releases.

An earthquake is the sudden shaking of the ground caused by a release of stored energy in the lithosphere. Millions happen every year, but most are too small to feel. Large ones can destroy cities and trigger tsunamis. In this lesson you will learn how earthquakes occur, how they are measured, and how to compare their sizes with a little math.

Faults and elastic rebound

A fault is a fracture in rock along which blocks have moved. Plate motion slowly loads rock with stress. The rock bends like a ruler (it deforms elastically) while the sides of the fault stay stuck by friction. When the stress exceeds the strength of the fault, it slips suddenly and the strained rock snaps back. This is the elastic rebound idea, proposed by Harry Fielding Reid after the 1906 San Francisco earthquake. The energy spreads as seismic waves.

Types of fault

Fault type Motion Stress Typical setting
Normal Hanging wall slides down relative to footwall Tension (pulling apart) Divergent boundaries, rifts
Reverse (thrust, if the dip is low) Hanging wall moves up Compression (squeezing) Convergent boundaries
Strike-slip Blocks slide sideways Shear Transform boundaries (San Andreas)

The hanging wall is the block above an inclined fault plane, and the footwall the block below it.

Depth and distribution

Focus depth can be shallow (0 to 70 km), intermediate (70 to 300 km) or deep (300 to about 700 km). Shallow earthquakes are the most common and usually cause the most damage. Earthquakes occur mainly along plate boundaries. Most of the energy (roughly 80%) is released in the circum-Pacific belt, often called the Ring of Fire.

Magnitude vs. intensity

Magnitude measures the energy released at the source and has one value per earthquake. Intensity measures the effects at a given place (shaking and damage), so it differs from place to place, being highest near the epicenter.

  • Magnitude scales: Charles Richter introduced his local magnitude scale in 1935. Today scientists mainly report the moment magnitude (Mw), which is based on the fault area, the average slip and the rock's rigidity and works well for large earthquakes.
  • Intensity scale: the Modified Mercalli scale uses Roman numerals I (not felt) to XII (near-total destruction) based on observed effects.

Magnitude scales are logarithmic. Each increase of one unit means about 10 times larger ground-motion amplitude and about 31.6 times more energy.

Comparing energy

A widely used relation (Gutenberg-Richter) for the radiated energy E in joules is:

log10(E) = 1.5 M + 4.8

So each step of 1 in M multiplies energy by 10^1.5, which is about 31.6.

Python Energy by magnitude

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

So a magnitude 8 earthquake releases about 1,000 times more energy than a magnitude 6.

How big can they get?

The largest earthquake ever recorded by instruments was the 1960 Valdivia earthquake in Chile, with moment magnitude about 9.5. The 2011 Tohoku earthquake in Japan was about 9.0 to 9.1. Earthquakes this large occur at subduction zones, where huge areas of the plate interface can slip at once. The longest and widest ruptures can generate tsunamis, long ocean waves caused when the sea floor suddenly moves up or down.

Frequency

Small earthquakes are far more common than large ones. Globally there are roughly 1 earthquake of magnitude 8 or above per year, ten times as many at magnitude 7 or above, and so on. The table below is a rough guide.

Python How often? A rough rule

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Safety

  • Drop, cover and hold on during shaking.
  • Buildings with flexible, reinforced designs and secure foundations survive better.
  • In coastal areas, if you feel long or strong shaking, move to high ground without waiting for a warning.
  • Earthquakes cannot yet be predicted precisely in time and place. Forecasts give probabilities over years or decades.

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. Which type of fault forms when blocks are pulled apart, and the hanging wall moves down?

    Tension makes the hanging wall slip down along a normal fault.
  2. 2. What is the difference between magnitude and intensity?

    An earthquake has one magnitude but many intensity values, depending on location.
  3. 3. About how many times more energy does a magnitude 7 earthquake release than a magnitude 6?

    Energy grows by a factor of 10^1.5, about 31.6, per magnitude unit.
  4. 4. What does elastic rebound describe?

    Rock deforms elastically until the fault slips, and then the strain is released.

Summary

  • Earthquakes happen when stressed rock slips along a fault; the energy travels as seismic waves.
  • Fault types: normal (tension), reverse (compression), strike-slip (shear).
  • Magnitude (moment magnitude) measures energy; intensity (Mercalli) measures effects.
  • Each magnitude step: about 10 times the amplitude and about 31.6 times the energy.

Next: Volcanoes and Hotspots