Skip to content
Tutorials Center
My learning

Topics

Lesson 7 of 38 · Maps and Geographic Skills

Map Scale, Distance and Direction

Read map scales, convert map distances to real distances, use the compass rose and bearings, and give grid references with confidence.

A map is a shrunken picture of the world. To use one you need to know how much it is shrunk (the scale), which way is which (the direction) and how to point to a place (the grid reference). These are basic skills for hiking, travel, exams and everyday life.

Map scale

Scale is the ratio between a distance on the map and the same distance on the ground. It appears in three forms.

  1. Ratio (representative fraction): 1:50,000 means 1 unit on the map equals 50,000 of the same units on the ground. It works with any unit.
  2. Statement: "1 cm represents 500 m".
  3. Line (bar) scale: a ruler drawn on the map. It stays correct if the map is enlarged or shrunk on a photocopier, which makes it very useful.

To convert, remember that 1 km = 100,000 cm.

At 1:50,000: 1 cm on the map = 50,000 cm on the ground = 500 m. So a route measuring 6 cm on the map is 3 km long.

At 1:250,000: 1 cm = 2.5 km.

Large scale and small scale

A large-scale map shows a small area in great detail (for example 1:10,000, a neighborhood). A small-scale map shows a large area with little detail (for example 1:50,000,000, the world). The names can feel backwards: the bigger the fraction (1/10,000 is bigger than 1/50,000,000), the larger the scale.

Scale Typical use Detail
1:1,000 to 1:10,000 Town plans, site maps Buildings visible
1:25,000 to 1:50,000 Hiking maps Paths, contours
1:250,000 to 1:1,000,000 Road atlas, region Main roads, towns
1:10,000,000 or smaller World map Countries only

When an exam gives a scale of 1:50,000, write "1 cm = 500 m" at the top of your working. It prevents zero errors.

Measuring distance

On a map, measure with a ruler. For a straight line this is easy. For a winding road, lay a piece of string or the edge of paper along the road, mark it, and then measure against the line scale. The result is the real distance along the ground (assuming it is flat; hills add some extra length).

JS Map distance to ground distance

Press Run (or Ctrl + Enter) to see the console output here.

No output.

Notice how doubling the scale denominator doubles the ground distance for the same map length.

Direction

The compass rose

North is usually at the top of a map, but always check for a north arrow. The four cardinal points are north (N), east (E), south (S), west (W). Between them lie the intercardinal points: NE, SE, SW, NW. A compass rose may show 16 points in total.

A handy memory phrase: "Never Eat Soggy Waffles" going clockwise from the top.

Bearings

A bearing is a direction given as an angle measured clockwise from north, from 0° to 360°, usually with three digits:

Direction Bearing
North 000°
East 090°
South 180°
West 270°
North-east 045°

A bearing of 225° is south-west. To find the back bearing (the direction from the other place back to you), add or subtract 180°. If you walk on 070°, the way back is 250°.

Maps use three kinds of north: true north (towards the North Pole), grid north (the vertical lines on the map's grid) and magnetic north (where a compass needle points, which wanders slowly and differs from true north by an angle called the declination). For accurate navigation you correct for this difference, and the map's margin tells you its value for that year.

flowchart LR
    A["True north<br/>geographic pole"] --- B["Grid north<br/>map grid lines"]
    A --- C["Magnetic north<br/>compass needle"]
    C -.->|"differs by declination"| A

Three norths used in navigation.

JS Compass points and back bearings

Press Run (or Ctrl + Enter) to see the console output here.

No output.

Grid references

Many maps are covered by a grid of numbered lines, so a place can be described by numbers. On a hiking map the vertical lines are called eastings (they number the distance east) and the horizontal lines are northings.

Rule: along the corridor, then up the stairs. Read the easting (left-right) first, then the northing (up). A four-figure grid reference such as 3472 names the whole square whose bottom-left corner is at easting 34 and northing 72. A six-figure reference, such as 347725, divides that square into tenths to point to a place within it. Each square at 1:50,000 normally represents 1 km by 1 km, so six figures locate a position to about 100 m.

Three map skills

Scale How much shrunk
Direction Bearings, compass
Grid refs Across, then up
1 / 2

The next program converts a six-figure grid reference into a position in meters inside a 1 km square. It is a helper that applies the rule above, not a real map lookup.

JS Six-figure grid reference reader

Press Run (or Ctrl + Enter) to see the console output here.

No output.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. On a 1:50,000 map, 4 cm represents what ground distance?

    1 cm = 50,000 cm = 500 m, so 4 cm = 2,000 m = 2 km.
  2. 2. Which is a large-scale map?

    The smaller the denominator, the larger the scale: 1:5,000 shows a small area in great detail.
  3. 3. What is the back bearing of 040°?

    Add 180° to 040° to get 220°.
  4. 4. In a grid reference, which number comes first?

    Read the easting (across) first, then the northing (up).

Summary

  • Scale links map length to ground length; ratio, statement and line scales are common.
  • Large-scale maps show small areas in detail; small-scale maps show large areas.
  • A bearing is a clockwise angle from north (000° to 360°); the back bearing differs by 180°.
  • Maps use true, grid and magnetic north; the difference between true and magnetic is declination.
  • Grid references give eastings first, then northings.

Next: Contour Lines and Relief