Skip to content
Tutorials Center
My learning

Topics

Lesson 24 of 39 · Quantum Statistics: Fermi-Dirac and Bose-Einstein

The Fermi Gas at Zero Temperature

Fill single-particle states up to the Fermi energy, derive the density of states, compute Fermi energy, Fermi temperature and degeneracy pressure for metals with runnable code.

Conduction electrons in a metal behave, to a surprisingly good first approximation, like a gas of non-interacting spin-1/2 fermions in a box. But this gas is nothing like the classical gas: even at absolute zero it carries enormous energy, because the exclusion principle forces electrons into higher and higher states. This lesson builds that picture and computes its key numbers.

Filling the states

At T = 0 the Fermi-Dirac distribution becomes a step: every state with ε < μ is full and every state above is empty. The chemical potential at zero temperature is called the Fermi energy E_F. To find it we need to count states.

A free particle of mass m in a box of volume V has energy ε = ħ²k²/2m. States in wavevector space are spaced evenly with density V/(2π)³ per unit volume of k-space. Each wavevector holds two spin states. The number of states with wavevector below k is

Text
N(k) = 2 · V/(2π)³ · (4π/3) k³ = V k³ / (3π²)

Setting N(k_F) = N gives the Fermi wavevector k_F = (3π² n)^(1/3) with n = N/V, and so

Text
E_F = ħ² k_F² / 2m = (ħ² / 2m) (3π² n)^(2/3)

The Fermi temperature is T_F = E_F / k. It is not a real temperature of the gas, but a measure: the gas is "degenerate" (quantum-dominated) when T ≪ T_F.

Density of states and energy

Differentiating N(ε) gives the density of states:

Text
g(ε) = dN/dε = (V / 2π²) (2m/ħ²)^(3/2) √ε

At T = 0 every state below E_F is occupied, so

Text
N = ∫₀^(E_F) g(ε) dε          →   g(E_F) = 3N / (2 E_F)
U₀ = ∫₀^(E_F) ε g(ε) dε  =  (3/5) N E_F

The average energy per electron is (3/5) E_F, not zero. The associated degeneracy pressure is P = (2/3) U₀/V = (2/5) n E_F. It is a purely quantum pressure that persists at T = 0 and keeps matter from collapsing: it is also what supports white dwarf stars against gravity (a relativistic version applies there).

Numbers for real metals

Electron densities for simple metals come from measured lattice constants and valences. The code uses typical room-temperature values (in units of 10²⁸ m⁻³): Li 4.70, Na 2.65, K 1.40, Cu 8.47, Ag 5.86, Au 5.90, Al 18.1. Free-electron theory is a rough model, so treat the resulting E_F as a good first estimate.

Python Fermi energy, temperature and pressure of metals

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The output shows E_F of a few eV for every metal and T_F of tens of thousands of kelvin (copper comes out at about 7.0 eV and 8 × 10⁴ K). Room temperature, T ≈ 300 K, is thus only about 0.4 percent of T_F: the electron gas in a metal is extremely degenerate. Degeneracy pressures of order 10 GPa or more are balanced by the electrostatic attraction between electrons and ions.

Electrons do not have a classical equipartition energy of (3/2) kT in a metal. At 300 K that would be about 0.04 eV, about 100 times smaller than the actual (3/5) E_F ≈ 4.2 eV for copper.

Verifying the counting numerically

We can check the algebra by integrating the density of states. The next example builds g(ε) for copper, integrates it up to E_F to recover N, and computes the mean energy per electron.

Python Integrate the density of states

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

The shaded area is the whole electron population: a thick slab of states, all filled, up to a sharp edge at E_F. Only electrons near that edge can change state when the temperature or an electric field disturbs the gas, which is the key idea of the next lesson.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. The Fermi energy of a free electron gas depends on the electron density as

    E_F = (ħ²/2m)(3π²n)^(2/3).
  2. 2. What is the average energy per electron at T = 0?

    ∫ε g(ε) dε over ∫g(ε) dε with g ∝ √ε gives 3/5.
  3. 3. For copper, T_F is about 8×10⁴ K. A gas at 300 K is therefore

    T/T_F is about 0.004, so the Fermi-Dirac distribution is almost a step function.
  4. 4. What is degeneracy pressure?

    Even at zero temperature fermions occupy states of high momentum, which pushes outward on the walls.

Summary

  • At T = 0 fermions fill states up to E_F = (ħ²/2m)(3π²n)^(2/3); T_F = E_F/k.
  • g(ε) ∝ √ε, U₀ = (3/5) N E_F, and P = (2/5) n E_F (degeneracy pressure).
  • Metals have E_F of a few eV and T_F of order 10⁴ to 10⁵ K, so room temperature is very cold for electrons.

Next: The Degenerate Fermi Gas at Finite Temperature