Skip to content
Tutorials Center
My learning

Topics

Lesson 4 of 37 ยท Getting Started

Accessories and a Starter Shopping List

Plan your first Raspberry Pi purchase: power supply, microSD card, case, cooling, cables, breadboard, resistors and LEDs, with a budget calculator.

A Raspberry Pi board by itself is not enough to get started. Unlike a laptop, it comes with no power supply, no storage, no case and no screen. Buying the right extras the first time saves you from a week of waiting for the postman and from strange problems caused by a weak power adapter or a slow memory card. This lesson lists what you really need, what is nice to have, and what to avoid.

The essentials

You cannot use a Pi without these:

  1. A power supply. Buy the official one for your model if you can. A Pi 4 wants 5 V and 3 A over USB-C. A Pi 5 wants 5 V and 5 A (27 W) for full USB power. A weak phone charger often causes random reboots and a lightning-bolt warning on screen.
  2. A microSD card. The card is your hard drive. Choose a reputable brand, at least 16 GB, preferably 32 GB, with an A1 or A2 application rating. A cheap no-name card is the number one cause of corrupted installs.
  3. A way to put the OS on the card. A card reader on your laptop, or the SD slot if it has one.
  4. A display cable, if you plan to use a screen. Pi 4 and Pi 5 use micro-HDMI to HDMI cables. Pi Zero uses mini-HDMI. This is a common surprise.

If you plan to work headless (no monitor, controlling the Pi from your laptop over the network), you can skip the display, keyboard and mouse entirely. You will learn that in First Boot and Headless Setup.

Nice to have

  • A case. Protects the board from dust and shorts. Pick one that leaves the GPIO header accessible if you want to wire things.
  • Cooling. A heatsink for the Pi 4, the official active cooler for the Pi 5. Cooler boards run faster for longer.
  • A USB keyboard and mouse for your first session.
  • An Ethernet cable. Wired networking is the most reliable way to set up a headless board.
  • A USB SSD. Faster and longer-lasting than an SD card for servers.

The electronics kit

For the GPIO chapters you also need a few cheap electronic parts:

Part What it is for
Breadboard A reusable plug-in board for building circuits without soldering
Jumper wires (male-to-female and male-to-male) Connect the Pi header to the breadboard
LEDs (several colors) The classic first output
Resistors, 220 to 330 ohms Limit the current through an LED
Push buttons Simple inputs
Resistors, 10 kilohms Pull-ups and pull-downs, sometimes
Temperature and humidity sensor (DHT22 or similar) First sensor project
Ultrasonic distance sensor (HC-SR04) Range finding
PIR motion sensor Motion detection
Camera Module Photos and video

Many shops sell a bundle that includes most of these. Check that a kit lists the exact connector for your model before buying.

Starter kit

Power supply Official, right amps
microSD card 32 GB, A1 or A2
1 / 2

What to avoid

Do not skimp on the power supply or the SD card, and do not power a Pi from a computer's USB port: it cannot supply enough current. Avoid very long, thin USB cables because they lose voltage. Avoid soldering headers on a Zero until you have practiced; buy one that comes with a header pre-soldered (often marked "H").

If your Pi shows a yellow lightning bolt or reboots at random, the power supply or cable is nearly always the cause. Swap them before you suspect the board.

Plan a budget

Prices change, so the numbers below are placeholders for you to edit. The point is to write the plan down and add it up before you click "buy".

Python Stand-in: budget calculator

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Check it against a checklist

Before ordering, compare your cart to a checklist. The next block marks missing items so you never forget the cable or the card.

Python Stand-in: shopping checklist

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

A note on safety

Static electricity rarely kills a Pi, but touch a grounded metal object before handling bare boards. Never connect or disconnect wires on the GPIO header while the Pi is powered. Place the board on a non-conductive surface; a metal desk can short the pins on the underside. The Pi itself runs at harmless voltages, but never open or modify a mains power supply.

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. What is the most common cause of random reboots on a new Pi?

    A phone charger or thin cable that cannot deliver enough current causes under-voltage and reboots.
  2. 2. Which items are absolute essentials for a first boot?

    Without power and a storage card holding the operating system, the Pi cannot boot.
  3. 3. What is a headless setup?

    Headless means you control the Pi remotely, so you need no display or input devices.
  4. 4. Why buy resistors for an LED circuit?

    A resistor in series limits current. Without it an LED can draw too much and be damaged.

Summary

  • You need a board, a proper power supply, a good microSD card and a way to write it.
  • A case, cooling, an Ethernet cable and an SSD are useful extras.
  • A breadboard kit with LEDs, resistors and wires covers the GPIO chapters.
  • Buy brand-name power and storage; avoid weak chargers.

Next: Raspberry Pi OS and the Imager