Skip to content
Tutorials Center
My learning

Topics

Lesson 15 of 39 ยท Decimals and Percentages

Decimals and Place Value

Extend place value past the decimal point, read and write decimals, compare and round them, and see how decimals relate to fractions with denominators of ten.

Whole numbers stop at the ones place. But money has cents, a race has hundredths of a second, and a medicine dose has fractions of a milligram. Decimals extend place value to the right, past a dot called the decimal point, to write numbers between whole numbers.

The rule you already know still holds: each place is worth ten times the place to its right. Going right past the ones place, each place is worth one tenth of the one before.

Places after the decimal point

Place Hundreds Tens Ones . Tenths Hundredths Thousandths
Value 100 10 1 . 1/10 1/100 1/1,000

In 3.472, the digits are 3 ones, 4 tenths, 7 hundredths and 2 thousandths:

3.472 = 3 + 4/10 + 7/100 + 2/1,000

Notice that the places to the right of the point end in -ths (tenths, hundredths), not "-s" (there is no "oneths"). The point itself separates whole units from parts.

Some countries write a decimal comma (3,472) instead of a point. The meaning is the same.

Reading and writing decimals

Read the whole part, say "and" or "point", then read the digits after the point one by one, or as a number with the last place's name.

  • 0.7: "seven tenths" or "zero point seven".
  • 0.25: "twenty-five hundredths".
  • 4.06: "four point zero six".

Write a zero before the point when the number is less than 1 (0.5, not .5) to avoid misreading.

Python Break a decimal into places

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Trailing zeros

0.5, 0.50 and 0.500 are all the same value. Zeros added to the end of a decimal do not change it, just as 7 = 7.0. But a zero between the point and another digit does matter: 0.05 is not 0.5.

In science, extra zeros can show precision (0.50 g suggests measured to hundredths), but in pure arithmetic they carry no extra value.

Comparing decimals

Line up the decimal points and compare place by place from the left. Pad with zeros if it helps.

Compare 0.8 and 0.75. Pad: 0.80 and 0.75. Tenths: 8 > 7, so 0.8 > 0.75. A common error is to think 0.75 is bigger because 75 is bigger than 8. Length does not decide the order of decimals, unlike whole numbers.

Order 0.3, 0.29, 0.301: pad to thousandths: 0.300, 0.290, 0.301. From least: 0.29 < 0.3 < 0.301.

Python Sort decimals

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

Rounding decimals

The rule is the same as for whole numbers. To round to the nearest hundredth, look at the thousandths digit: 5 or more rounds up, 4 or less leaves the hundredths digit alone.

  • 3.4672 to one decimal place: look at 6, round up: 3.5.
  • 3.4672 to two decimal places: look at 7, round up: 3.47.
  • 3.4632 to two decimal places: look at 3, stay: 3.46.

A "decimal place" counts digits after the point. Rounding 9.96 to one decimal place gives 10.0, because the carry runs through.

Python Round to decimal places

Press Run (or Ctrl + Enter) to see the result here.

Program input ยท what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with input()), it gets the next line from this box.

(The standard round() function in Python uses banker's rounding on exact halves, so we use Decimal with half-up rounding, the convention used in school math.)

Decimals and fractions

Any decimal is a fraction with a denominator that is a power of ten:

  • 0.7 = 7/10
  • 0.25 = 25/100 = 1/4
  • 0.125 = 125/1,000 = 1/8

Place the digits over 10, 100 or 1,000 (one zero per decimal place), then simplify. Going the other way is covered in the lesson on fractions, decimals and percentages.

Common mistakes

  • Thinking more digits means a bigger decimal.
  • Misplacing the point when multiplying or dividing by 10.
  • Reading 0.05 as "five tenths".
  • Rounding by looking at the wrong digit.

Check your understanding

Quick check ยท 4 questions

of 4 answered You scored / 4 ยท perfect!

  1. 1. What is the value of the digit 7 in 3.472?

    The digits after the point are tenths (4), hundredths (7), thousandths (2).
  2. 2. Which is greater?

    0.8 = 0.80, and 80 hundredths is more than 75 hundredths.
  3. 3. Round 3.4672 to two decimal places.

    The thousandths digit is 7, so the hundredths digit 6 rounds up to 7.
  4. 4. What is 0.25 as a simplified fraction?

    0.25 = 25/100, and dividing by 25 gives 1/4.

Summary

  • Decimal places continue place value to the right: tenths, hundredths, thousandths.
  • Each place is one tenth of the place to its left.
  • Trailing zeros do not change a decimal's value; zeros before another digit do.
  • Compare decimals place by place from the left, padding with zeros.
  • Round by checking the digit just after the place you need.

Next: Decimal Operations