Skip to content
Tutorials Center
My learning

Topics

Lesson 15 of 37 · Analog and PWM

Voltage Dividers

Learn the voltage divider formula, use it to read resistive sensors like LDRs and thermistors, scale 5 V signals down for 3.3 V boards and measure battery voltage.

An Arduino analog pin measures voltage, but many sensors change their resistance: a light-dependent resistor (LDR) gets less resistive in bright light, a thermistor changes with temperature, a flex sensor with bending. A voltage divider turns resistance into voltage, and it is also the way to scale a voltage down to a range the board can handle. It is two resistors and one formula, and it will appear in a large share of your projects.

The circuit and the formula

Two resistors in series connect between a supply voltage Vin and ground. The voltage at the junction between them is a fraction of Vin:

TEXT
Vout = Vin × R2 / (R1 + R2)

R1 is the resistor on the supply side (top), R2 the one on the ground side (bottom), and Vout is measured across R2.

flowchart TD
    A["Vin"] --> R1["R1"]
    R1 --> J["Vout (to analog pin)"]
    J --> R2["R2"]
    R2 --> G["GND"]

Figure: the junction between R1 and R2 gives Vout = Vin x R2 / (R1 + R2).

If R1 = R2, then Vout is exactly half of Vin. A potentiometer is a divider whose ratio you change by turning the knob. The divider only gives that voltage if almost no current is drawn from the junction; the ADC input draws almost none, which is why it works.

C Stand-in: calculate divider outputs

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with scanf or fgets), it gets the next line from this box.

Reading a resistive sensor

Put the sensor on one side of the divider and a fixed resistor (usually near the sensor's mid-range resistance) on the other. As the sensor's resistance changes, Vout moves and analogRead() follows.

An LDR might measure about 1 kΩ in bright light and 100 kΩ in the dark. With a 10 kΩ fixed resistor on the ground side and the LDR on top (between 5 V and the junction), bright light gives a high voltage and darkness a low one:

C Stand-in: LDR in a divider, from resistance to reading

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with scanf or fgets), it gets the next line from this box.

The relation is not linear, but for a night light that only needs "bright or dark", that does not matter. For a thermistor you convert the resistance using a formula from the datasheet (the Steinhart-Hart or Beta equation) before turning it into degrees. Solve the divider for the unknown resistor:

TEXT
Rsensor = R2 × (Vin / Vout − 1)       when the sensor is R1 (top)
C Stand-in: recover an unknown resistance from a reading

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with scanf or fgets), it gets the next line from this box.

Notice that the formula needs only the ratio Vout/Vin; the supply voltage cancels out. That is a useful property: the result does not depend on whether the board runs at 5 V or 3.3 V.

Level shifting and measuring higher voltages

The ADC cannot measure more than its reference voltage. To measure a larger voltage, divide it down. For a 12 V battery and a 5 V ADC, a 30 kΩ over 10 kΩ divider gives 12 × 10 / 40 = 3 V. A 2:1 ratio is also the standard trick for a 5 V logic output feeding a 3.3 V board input: 1 kΩ above and 2 kΩ below gives 5 × 2 / 3 = 3.33 V.

C Stand-in: design a divider for a battery monitor

Press Run (or Ctrl + Enter) to see the result here.

Program input · what you'd type while the program runs

Type the answers before you press Run, one per line. Each time the program reads a line (with scanf or fgets), it gets the next line from this box.

The computed 18.8 kΩ is not a standard value. Rounding down to 18 kΩ would put 5.14 V on the pin at 14.4 V, over the limit, so we round up to 22 kΩ, which gives 4.5 V at full charge and a safe margin. Always check the worst case, not the typical case.

Divider limits

  • Current drain. A divider always passes current (V / (R1 + R2)). For battery projects use large values (100 kΩ and up) and add a small capacitor to the ADC pin to help it charge.
  • High source resistance. The ADC wants a source under about 10 kΩ. A divider with 100 kΩ resistors needs a 100 nF capacitor from the junction to GND, and slower sampling.
  • Loading. Anything connected to Vout draws current and changes the voltage. A divider is for measuring, not for powering a load.
  • Tolerance. Standard resistors are ±5% (or 1% for metal film); that error carries into your reading.

Check your understanding

Quick check · 4 questions

of 4 answered You scored / 4 · perfect!

  1. 1. In Vout = Vin x R2 / (R1 + R2), where is Vout measured?

    Vout is the voltage between the junction and ground, which is the voltage across R2.
  2. 2. R1 = 10 kohm, R2 = 20 kohm, Vin = 6 V. What is Vout?

    6 x 20 / 30 = 4 V.
  3. 3. Why does the divider reading of a resistive sensor not depend on the supply voltage once you use the ratio?

    analogRead measures Vout relative to the same supply that feeds the divider, giving a pure ratio.
  4. 4. What is a drawback of a divider with very small resistors?

    Current is V divided by the total resistance, so small resistors draw more.

Summary

  • A voltage divider outputs Vout = Vin × R2 / (R1 + R2).
  • It turns a changing resistance (LDR, thermistor) into a voltage the ADC can read.
  • Solve the formula backward to compute the sensor's resistance from a reading.
  • Dividers scale high voltages down for the ADC and 5 V signals down for 3.3 V inputs.
  • Mind current drain, source impedance, loading and resistor tolerance.

Next: PWM and analogWrite